1.a Calculate the equivalent height of mercury column for the first question's gauge pressure. Density of air = 0.0765 lb/ft2 Specific gravity of mercury (Hg) = 13.5 1.b Assume that you are sitting in a room at 28 psi (absolute pressure). Determine the gauge pressure. 13.3

Q: Determine the force in member CB of the truss, and state if the member is in tension or compression.…

A:

Q: Determine the coordinates of the mass center of the welded assembly of uniform slender rods made…

A:

Q: A-Solve the following 2nd ODE by Laplace transformation k 12 +40 y" + 4y = 0. y(0) = 2. y'(0) = 2

A:

Q: . Find the force acting on the parts AB, AG, BC, BG by using the joint method and tell them whether…

A:

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: Given Required  Force in each member

Q: A negative internal bending moment M causes a beam element to O rotate counterclockwise bend concave…

A: Bending moment at a given section can cause Sagging (concave upward) or hogging (concave downward)…

Q: QUESTION 2 PROBLEM 2: Calculate the components of the forces at B and C. A D E F b Given: P= 21 kN a…

A:

Q: Problem Instructions: The cutting plane should pass through the midspan of the beam. From the…

A: Given data :

Q: 4. The copper shaft (G= 44 GPa) is bonded to A the aluminum shaft (G= 26 GPa) at B point and their…

A: Data Given: GAB = 44 GPaGBC = 26 GPaLAB = 150 mmLBC = 120 mmrAB = 28 mmrBC = 45 mmt = 4.2 mmτAB =…

Q: Solve the internal forces on the given beams.

A: Consider the free body diagram of the given beam as shown below.

Q: Solve the internal forces on the given beams.

A:

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: support reaction: ∑MB=0RA×6+5000×5×cos45=0RA=-2946.278 N∑FY=0RA+RB-5000=0-2946.278…

Q: Situation 1: The 300-lb force is to be resolved into components along lines a-a' and b-b'. a 300 lb…

A: Given data in question  Load Angle To find out  Components

Q: 2- A force acting on a body may....... A. Change its motion C. Retard its motion B. Balance the…

A: Force is external force which is used to induce stress and to change the state of rest or motion of…

Q: C. (8-1²) dr = r²³ sine do fo 2

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: 1-z? 1. f(z) = (by Definition) 22 %3D Find the derivation

A: using u/v rule of derivatives we can get answer

Q: Show that A=n(1-Sr)

A: Given :- a soil is in three phase consists of solid, water and air.   To show :- A = n( 1- Sr)

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: 2) Find the next term in the sequence below. -6,-1, 4,

A: Objective: To determine the next term in the given sequence.   Given sequence: -6, -1, 4, ___   The…

Q: Problem: For the beam and loading shown, determine (a) the equation of the elastic curve, and (b)…

A:

Q: 2.Value of R1 in Ib b=3.75 inches h=4.12 inches P= 1991 Ib A= 4.83 ft B= 6.23 ft

A: Given: The load P is 1991 lb. The height h is 4.12 in. The width b is 3.75 in. The value of A is…

Q: Hiwe A bar with constant ss-section area(Aland unit weight () is subjected to axial force ce) in…

A:

Q: following Integral function.

A: Given:- To find:- Integral function

Q: Determine the center of mass in y axis (ỹ) of the homogeneous solid block. L = 0.35m II

A:

Q: Consider the following statements: A. Members of the truss are acted upon by two equal opposite…

A: Answer : Option (A)  A and B is correct.

Q: 12" 6" %3D4'

A:

Q: If A = 75°, C = 37° and b = 6, work out the length of a. %3D %3D B a C [C

A: Given data:  A=75∘C=37∘b=6

Q: ? If n is the ratio of internal and external diameter of a hollow shaft, the ratio of the weight of…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.