1.89 A 12-in.-diameter circular plate is placed over a fixed bottom plate with a 0.1-in. gap between the two plates filled with glycerin as shown in Fig. P1.89. Determine the torque required to rotate the circular plate slowly at 2 rpm. Assume that the velocity distribution in the gap is linear and that the shear stress on the edge of the rotating plate is negligible. Rotating plate Torque 0.1-in. gap

1.89 A 12-in.-diameter circular plate is placed over a fixed bottom plate with a 0.1-in. gap between the two plates filled with glycerin as shown in Fig. P1.89. Determine the torque required to rotate the circular plate slowly at 2 rpm. Assume that the velocity distribution in the gap is linear and that the shear stress on the edge of the rotating plate is negligible. Rotating plate Torque 0.1-in. gap

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A tank of water sits on a cart with frictionless wheels as shown. The cart is attached to a mass and…

A: Given data: The coefficient of static friction of the mass with the ground is µ = 0.50. The…

Q: !A rectangular gate having a width of 1.5 m is located in sloping side of a tank as shown in fig.…

A: Given, W = 1.5 m

Q: 1. For the shown conic body which rotating with constant angular velocity 10 rad/s, find the torque…

Q: Calculate for the temperature, pressure and density on the wing at that altitude *

Q: A vertical gap of 0.1 mm contains a fluid of viscosity (2 Pa.s). A thin metallic plate sheet (0.2 m…

A: Givent=0.1mm=0.1×10-3 mμ=2 Pa-sA=0.2m×0.3mV=0.1 m/sw=60N

Q: A cube 2.2 feet on an edge has its lower half of s.g. = 4.8 and upper half of s.g. = 2. in a…

A: Given6A=4.86B=2.96C=4.66D=3.95

Q: A 3d block with the dimensions of 50cm by 30cm by 20cm and a weight of 450 N, is going to be moved…

Q: 5.13 A hydrometer is a device for indicating the specific gravity of liquids. Figure 5.21 shows the…

Q: b) An incompressible fluid with kinematic viscosity of 7.4 x 10-7 m/s and specific gravity of 0.88,…

Q: Solve with the correct units 6. A square block weighing 1.1 kN and 250 mm on an edge slides down in…

A: GivenW=1.1kNa=250mm=0.250mθ=20ot=6μm=6×10-6mν=7mPa.s =7×10-3 Pa. s

Q: Answer fully

Q: Neglecting losses, determine the x- and y-components of force needed to hold the tee (Fig. 3.63) in…

A: At 1-

Q: 2.25 A fire-fighting nozzle is attached to a 3-in. flexible hose in which the pressure is 100 psi.…

A: In this question, the pressure at the inlet of pipe is given and the diameters of the pipe at the…

Q: If 1 cup of cream having a density of 1010 kg/m³ is turned into 3 cups of whipped cream, determine…

Q: Q A piezometer was connected to a pipe to measure the pressure of water. The rise of water level in…

Q: A 1.2 m x 1.2 m square gate located in the vertical side of an open tank is pivoted about the…

A: To Find : The magnitude of hydrostatic force acting on the square gate.Given : The dimension of…

Q: Q6: A force of 1600 N is applied uniformly on a piston of 8 cm diameter. Determine the pressure on…

A: Given Force, F=1600N diameter, d=8 cm⇒8*10-2 m Area, A=π4.d2 A=π48*10-2 2 A=5.025*10-3 m2

Q: What is the relationship between the height of column of fluid and its exit velocity? What…

A: This question is based on the concept of fluid mechanics

Q: prove that the pressure at a point in a fluid at rest, or in motion, is independent of direction as…

A: The basic property of a static fluid is pressure. For a static fluid, as shown by the following…

Q: Problem 2 (30 points): The manometer shown is closed to the atmosphere. The pressure at point A is…

A: Given: The pressure at point A is PA=9000 Pa. The pressure at point B is PB=8000 Pa. The dimension…

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

1.89 A 12-in.-diameter circular plate is placed over a fixed bottom plate with a 0.1-in. gap between the two plates filled with
glycerin as shown in Fig. P1.89. Determine the torque required to rotate the circular plate slowly at 2 rpm. Assume that the
velocity distribution in the gap is linear and that the shear stress on the edge of the rotating plate is negligible.
Rotating plate
قل
Torque
FIGURE P1.89
0.1-in. gap

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: GIVEN VALUES IN QUESTION

VIEW

Step 2: TORQUE DERIVATION

VIEW

Step 3: TORQUE CALCULATION

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

7.8 A pneumatic system is operated at a pressure of 1000 kPa. What diameter cylinder will be required to move a load requiring a force of 12 kN?
4. The space between two 6-in. long concentric cylinders is filled with glycerin (viscosity = 8.5 X 10³ lb-s/ft²). The inner cylinder has a radius of 3 in. and the gap width between cylinders is 0.1 in. Determine the torque and the power required to rotate the inner cylinder at 180 rev /min. The outer cylinder is fixed. Assume the velocity distribution in the gap to be linear. Refer to Fig. P1.3. Ans. 0.944 ft.-lb, 17.8 ft-lb/s
2.
3. A cylindrical buoy 600 mm in diameter and 1.8 m high weighs 205 kg. It i moored in salt water to a 12 m length of chain weighing 12 kg per m of its length. At high tide, the height of buoy protruding above water surface is 0.84. What could be the length of protrusion of the buoy if the tide dropped 2.1 m? Density of steel is 7,790 kg/m. Use density of water = 1000 kg/m³. W, = 205 kg %3D 0.6m 0 W = 205 kg 0.84 0.6m o 1.8m 2.1 m 0.96 BF, 1.8m D. BF', H' BF2 L Chain L' BF' Figure a: High Tide Figure b: Low Tide
5.3 The surface of water at a certain point in the swimming pool has a temperature of 27 °C at the atmospheric pressure of 101,325 kPa. The temperature at the bottom of the swimming pool is 10 °C. An air bubble with a diameter of 10 mm is let loose from the bottom. Calculate the depth of the swimming pool if the bubble has a diameter of 20 mm when it reaches the surface. HINT: Calculate the difference in pressure at the top and the bottom, and then use the relevant formula to determine the depth. Density of water = 1 000 kg/m³ (6) [11] TOTAL: 70
Solve with explanation
4. In combustion systems that burn hydrocarbon fuels, the carbon dioxide gas that is produced eventually escapes to the atmosphere thereby contributing to global warming. Calculate the density, specific weight, viscosity and kinematic viscosity of carbon dioxide at a pressure of 200 kPa absolute and 90°. Note: Refer the value of R at 90° at the Appendix of the reference's books.
W2.20
Determine:a. The shear stress acting on the bottom wall. b. The shear stress acting on a plane parallel to the walls and passing through the centerline between the two plates. c. Plot the shear stress variation versus the y direction.d. Repeat part (b) if the velocity is linear between the two plates and for the same value of V= 0.6 m/s at the centerline. Interpret your result.
4
Problem 2 The apparatus sketched in the figure below serves as a viscometer i.e. it can be used to measure the viscosity of a liquid. In the drawing, D is a large reservoir containing a viscous liquid A and E is a cylindrical tube of radius R, open at both ends, surrounding and coaxial with B, which is a cylindrical "bob" of radius êR that is dragged up through the fluid by a frictionless pulley system (C) utilizing a weight W. Determine a design equation that relates the viscosity of the liquid to the geometry of the system and the weight W. Hint: you can assume that the length of the cylindrical tube is sufficiently long for the flow to reach steady state. W E D B
How can the equivalent point forces of fluids be found?