1.7-1 An angle bracket having thickness 19 mm is attached to the flange of a column by two 16 mm diame- ter bolts (see figure). A uniformly distributed load from a floor joist acts on the top face of the bracket with a pres- sure p 1.9 MPa. The top face of the bracket has length L-200 mm and width b-75 mm. Determine the average bearing pressure o, between the angle bracket and the bolts and the average shear stress T in the bolts. (Disregard friction between the bracket and the column.)

1.7-1 An angle bracket having thickness 19 mm is attached to the flange of a column by two 16 mm diame- ter bolts (see figure). A uniformly distributed load from a floor joist acts on the top face of the bracket with a pres- sure p 1.9 MPa. The top face of the bracket has length L-200 mm and width b-75 mm. Determine the average bearing pressure o, between the angle bracket and the bolts and the average shear stress T in the bolts. (Disregard friction between the bracket and the column.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

No wrong answer pls
For the connection shown, the average shear stress in the 12-mm-diameter bolts must be limited to 220 MPa. Determine the maximum load P that may be applied to the connection. O 164 KN 149 kN O 94 KN O 109 kN O 122 kN
Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter. The connection is bottled at the web only. Assume x= 0.76 inch. 2. The shear lag coefficient U and the effective area Ae
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
The one end of a hollow square bar whose side is 10 with 1 thickness is under a tensile stress 102500 and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σall =243000 psi for pin material.
3. A threaded rod and nut arrangement are guided with two washers, upper and lower washers tightened into a base plate. Considering that the base plate carries a load of 120 kN including its self-weight which is distributed equally: a. Determine the stress on the lower washers before the buts are tightened. b. Determine the stress int the upper washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. Determine the stress int the lower washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. c. 44 mm Upper washer Base plate Lower washer 20 mm 22 mm 50 mm
O cd O efgh O ij O klmn O qrst V What is the line of action of which the section will yield in tension? All holes are the same diameter. O aflrsmgb O op t P n j h C d
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
3) will upvote anyone who will answer
A16mm–diameter steel rod AB is fitted to a round hole near end Cof the wooden member CD. For the loading shown, determine, (a) the distance bfor which the average shearing stress is 7Mpa a on the surfaces indicated by the dashed lines, (provide FBD and answer in mm)(b)the average bearing stress on the wood (provide FBD and answer in Mpa)
Five M20 8.8/ bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B-E43XX) with size of 5 mm. The design force transferred from beam to column is 300 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fü = 360 MPa. Determine the unit stress sustained by the weld