1.67 Figure P1.67(a) shows two transconductance amplifiers connected in a special configuration. Find v, in terms of vị and vz. Let gm = 100 mA/V and R = 5 k2. If v = v2 = 1 V, find the value of v,. Also, find v, for the case v = 1.01 V and vz = 0.99 V. (Note: This circuit is called a differential amplifier and is given the symbol shown in Fig. P1.67(b). A particular type of differential amplifier known as an operational amplifier will be studied in Chapter 2.)

1.67 Figure P1.67(a) shows two transconductance amplifiers connected in a special configuration. Find v, in terms of vị and vz. Let gm = 100 mA/V and R = 5 k2. If v = v2 = 1 V, find the value of v,. Also, find v, for the case v = 1.01 V and vz = 0.99 V. (Note: This circuit is called a differential amplifier and is given the symbol shown in Fig. P1.67(b). A particular type of differential amplifier known as an operational amplifier will be studied in Chapter 2.)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In an inverting op-amp, has the following. Rf=20K, R1=5K and Vin=3 volts. What is the gain of this Amplifier?
Introducion to Electronic Analysis and Design - CE05 To have a good amplifier Select one: a. The input resistance should be high b. the output resistance should be high c. the voltage gain should be equal to zero d. the current gain should be equal to zero Ssment CE255/EE255 (O1)- Dr. Mamoun Al-Mistar Jump to...
What are circuits can used to design Class B amplifier ? explain the important features ? for each
Q5. What type of amplifier is shown below? LM324 Vcc Vo Ri Vee %3D Vi Rf
VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D
Determine the maximum theoretical efficiency of RC-coupled class-A amplifier as shown in Figure Q2(a). Show every detail of the calculation steps. Vcc Ice R1 RL C2 IB R2 IE Figure Q2(a)
Four voltage sources of 3 V, 4V, 2V and 3V respectively are to be applied to the input terminal/terminals of “an" inverting amplifier. Design two different circuits for the two different cases with justified explanation and selection of proper resistances as per the requirements below: a) When an output of 4V is required (with phase shift). b) When an output of 8V is required (without phase shift) Note: Only inverting amplifier/amplifiers to be used for each case and all the voltage sources are to be used for each individual design as required in a) and b). 2.
Note : Value of K1 = 17; K2 = 49 Show the each equation part and Mention ans same as asking in question. There are must be 2 graphs. Read the 2 pictures clearly and ans all the question. For Example : "Compare T+,T- , Draw the transfer characteristics V0 and V1 " Mention like this then ase the question. formula should be taken from "Operational Amplifier and Linear Integrated Circuits, by Robert F. Coughlin and Fredrick F. Driscoll, 6th Edition, Pearson." this book.
C. A variable capacitor. O d. An amplifier. When operating in the saturation region, the current gain 'B' of the bipolar transistor increases Select one: OTrue O False Assume Is= 8x 105 A, B-100, and VA =-. For the circuit shown below and for -0.5 mA, the value of the transconduce Vcc=2 V Q1
Design a voltage follower amplifier circuit with a voltage divider on it. Assume that you have 60v voltage input voltage with a frequency of 60hz. Instead of using “Universal Op Amp 2" as a component, use the OPO7 Amplifier. What should be the values of your R1 and R2 to get a reading of a voltage output equal to 5.38 volts at exactly 20ms. The arrangement of your input should be, the one that is at the top most is the Voltage Input followed by the R1 and the lowest part is the R2. Draft17 Cursor 1 V(n005) Horz: 20.0054ms Vert: 5.3827036V What is the value of R2 in kilo ohms? No need to include the Units. R2 = k Ohms
e) For the amplifiers shown in the figure below, write and explain the formula for the V1 and Vout in relation to Vin. R6 R2 R3 R5 R1 R4 V. V. V, v,
4) Below is the small signal model of a multistage amplifier. Using this model, write the equationsthat you would need to determine the voltagegain. IMPORTANT: You only need to providethe equations that you would need to determinethe voltage gain. You DO NOT need to combine and simplify the equationsto determine a final expression for the voltagegain. Vin Vo Vb vo1 Rb R13 Vbe1 Vbe2 'e gm 1 Vbe1 gm 2 Vbe2 Rc2 Rc1 Re