helpSubjective Questions 1.5. What is quality of conformance from the producer'sperspective and how can it be achieved? 1.6. A company has accepted a contract to producea special electric motor. The number of direct labor hours required to produce the first motoris 250. If an 85% learning curve applies to the production of motor, then the number oflabor hours needed to produce the 4th motor is? 1.7. The direct labor times required toproduce the first four units of a new product are shown below Based on this data, what is theestimated learning or improvement rate? R Subjective Questions1.5. What is quality of conformance from the producer's perspective and how can it beachieved?1.6. A company has accepted a contract to produce a special electric motor. The numberof direct labor hours required to produce the first motor is 250. If an 85% learningcurve applies to the production of motor, then the number of labor hours needed toproduce the 4th motor is?1.7. The direct labor times required to produce the first four units of a new product areshown belowUnit Number Direct Labor Hours1,2001,020927.5867Based on this data, what is the estimated learning or improvement rate?1234

A learning curve is a graphical representation that shows how an increase in learning (measured on…

Answered: 1.5. What is quality of conformance…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

Lazer Technologies Incorporated (LTI) has produced a total of 20 high-power laser systems that could be used to destroy any approaching enemy missiles or aircraft. The 20 units have been produced, funded in part as private research within the research and development arm of LTI, but the bulk of the funding came from a contract with the U.S. Department of Defense (DoD). Testing of the laser units has shown that they are effective defense weapons, and through redesign to add portability and easier field maintenance, the units could be truck-mounted. DoD has asked LTI to submit a bid for 100 units. The 20 units that LTI has built so far cost the following amounts and are listed in the order in which they were produced: Use Exhibit 4A 5 and Exhibit 4A.6. UNIT COST HUMBER (5 MILLIONS) 10 $12.0 10.0 6.0 6.5 5.0 6.0 5.0 3.6 4.1 Learning rate UNIT COST NUMBER (S MILLIONS) 11 12 13 14 15 16 17. 18 % 19 20 $3.9 3.5 3.0 2.8 2.7 2.7 a. Based on past experience, what is the learning rate? Note: Do…
Name or state three elements that can unsettle or disrupt the learning curve ?
You have been asked to estimate the selling price per unit of a new production line of a certain product. Pertinent data are as follows: Direct labor rate Production material Factory overhead Packing costs Desired profit RO 15.00 per hour RO 375 per 100 items 125% of direct labor 25% of direct cost 30% of total manufacturing cost Past experience has shown that 83% learning curve applies to the labor required for production these items. The time to complete the first item has been estimated to be 1.86 hours. Use the estimated time to complete the 50h item as your standard time for the purpose of estimating the unit selling price.
Semana 1 2 4 80% 5 90% 6 100% LC % 60% A new equipment was installed with this learning curve. The material cost is $2.50 per unit. At this moment, the actual waste % is 5% for this process. The equipment capacity is 23401 unites per week. Determine the learning curve cost for the material. 30% 3 70%
9. Manufacturer Ċ went through serious process changes in order to eliminate unnecessary processes from the work flow. However they have to bare the slow down in the process for a while due to this transition. They want to estimate when they can reach to the expected performance level based on a 'learning curve' study. For a certain task they have measured a completion time of 137 minutes in the first time an average employee finished the renewed task. Please provide the values in the below table for three different learning rates and two different repetition units. 2nd 4th 13th 27th Learning Rate 70% 80% 60%
Given the following information from an assembly task: First cycle time: 35 seconds Learning rate of 90% a. Determine the predicted performance time of the 200th b. Determine the number of cycles it will take to reach the standard time of 14 seconds
A new training program at Arid Industries is intended to lower the learning-curve coefficient of a certain molding operation that currently costs $95.50/hour. The current coefficient is .87, and the program hopes to lower the coefficient by 10%. Assume that the time to mold the first product is 8 hours. If the program is successful, what cost savings will be realized when the 2000th piece is produced?
Berringer Designs hired a graphic artist. It is estimated that the artist's learning rate is at 70% and her first quarter's output amounted to 300 relatively equal job outputs, which took her a total of 50 hours to complete. Output is expected to double in every succeeding quarter. By the 5th quarter, based on learning curve estimates, what should the artist's average time (in hours) be for the units of output? Multiple Choice 17.15 hours 3.5 hours 12.005 hours 6.9 hours None of the answers is correct
Which of the many features of the KIS should we become most proficient in?
The Controlling Function What is the most important idea/concept that was generated in the controlling function? Can you explain this concept in your own words? Would you be able to provide a work place example to support your understanding of the new learning mentioned by you?
Week |1 2 LC% 30% 60% 3 70% 4 80% 5 6 90% 100% A new equipment was installed, and we estimate this learning curve percentages. The cost of labor per unit is $1.09. The Weekly capacity is 6302 units. Determine the labor learning cost for this equipment.
What is carefulness? Why should an organization ensure that it is exercising reasonable care in its normal operations?

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS