- 1.5 m 2 m Prob. 6–84

Q: Use the cantilever method and determine (approximately) the reactions at supports A and B. All…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subpartsfor…

Q: Angle of the resultant R (in degrees, measured counter-clockwise from the positive x-axis)

A:

Q: Z Z Z I = Ax IM IN Ay By

A:

Q: Assume w₁ = 870 N/m, v W₁

A:

Q: find the reaction of the wall at A on the lower shaft

A: balancing the two spheres first draw free body diagram of both sphere seperatly

Q: oblem 2 e truss shown carries the following uniform live load and concentrated e load. E G D 3 @4 m…

A:

Q: Determine the reactions at A and B for the steel bar and loading shown, assuming a close fit at both…

A: Given data:- Conditions given-Remove restriction at A and solve for the reactions Below bar figure…

Q: Determine the reaction at B for the beam shown below. |--3m+ O a. By = 131 kN ↑ O b. By = 131 kN ↓ O…

A:

Q: Determine the components of the reactions for the beam

A:

Q: The smooth pipe rests against the opening at the points of contact A, B, and Cand supports the force…

A: Given : F = 300 N Find : Magnitude of reaction at A and B?

Q: For the frame shown, determine the force reaction at fixed support D. A. B, and C are pins. provide…

A:

Q: Determine the components of the reactions for the beam. Please show all work

A: Please give helpful review

Q: Compute the internal reaction of member FG of the truss. F B= 60 KN 80 KN 14 m B A 4 m C 4 m E 4 m G…

A:

Q: DETERMINE THE REACTIONS AT A AND

A: To find support reaction

Q: 3000 lb 40° 4 ft B 6 ft A D 8 ft

A:

Q: 3. Determine the components of reaction at the fixed support A. Neglect the thickness of the beam.…

A: Given above given figure in Q 3 we have to find the support reactions at A

Q: Determine the components of the reactions for the beam

A:

Q: P= 10KN w 2kN/m

A:

Q: Determine the reaction at the support B. 500 N 400 N 0.5 m B 2 m 2 m

A:

Q: answer

A:

Q: Roller at A and pins at C and E. 18EN 4 KN/m -2m-

A: Degree of static indeterminacy -  Ds = re - 3 - rr here, re = Total reactions = 4 ( 3 of fixed…

Q: Determine the reaction at the support B. 500 N 400 N 0.5 m 2 m 2 т

A:

Q: 3. The distributed loading acts on the simply supported beam. The support at A is a pin and the…

A: A simply supported beam with hinged support at A and roller support at B with an equal overhang of…

Q: 22: Determine the reactions at the supports using the force method. El is cons Take Dy as a…

A: Using strain energy method : force method

Q: Determine the vertical component of the reaction D, at the pin support D

A:

Q: 3 kN 0.5 m 1.5 m 8 kN/m

A: Draw the figure.

Q: -2 m- -2 m- B 2m 2m 2 kN

A:

Q: (3) We want to determine whether the internal bending moment is zero, positive, or negative at…

A:

Q: 3. Given the figure below, compute for the reaction at A and B and maximum stress of the beam. The…

A: ##Calculation of Support reaction and Maximum stress##

Q: Vertical reaction at roller A in kN. RA Vertical reaction at roller C in kN. RC

A:

Q: Given the rod below (E = 70Gpa; a = 23 × 10-6 1/°C; diameter d = 50mm; AC = 400mm; BC = 800mm, P =…

A:

Q: Determine the reaction at the roller support in N. 100 N 200N 300 N 45° 30 I m 1 m i O 205 305 285 O…

A:

Q: 1000 N 3000 N 1000 N E b 1000 N 30 2 m -2 m 2 m-2 m

A:

Q: 3. For the system shown, a. Determine the equivalent force-couple 300 N 200N 400 N - 3m -4m system…

A: a) Determine the equivalent force-couple system at the base at C.   Equate force at C Fx =→ +ve Fy =…

Q: The reactions at the support for a simple beam loaded as shown. Neglect the weight of the beam. The…

A: Given: A simple beam with loadings  Required: Support reactions  Internal forces at C

Q: Determine the member end moment and reaction of the structure by using kanis method

A: The force of shear is a sensitive force on the surface. It's said to be the bending moment the…

Q: The solid shaft that is fixed connected at both ends has a diameter of 20 mm and a total length of…

A:

Loads and Reactive Forces

Loads are the external influences that a beam experiences under its working conditions. For instance, a beam may be subjected to shear loads, twisting loads, bending moment, and axial loads during its working conditions. Engineers primarily deal with beams and trusses in the civil engineering domain. Due to the influence of loads, it is very crucial to determine the induced stresses and deformation values. These values give an insight into the critical area of the beam that needs to be worked upon to make it fail-safe.