2.1.44 Consider the circuit shown in Figure P1.44. Determine the diode current Ipand diode voltage V, for (a) V, = 0.6 V and (b) V, = 0.7 V.+5 V3 ka2 ka2 kaFigure P1.44ww-ww.

First we will find Thevenin equivalent circuit from diode terminals. Thevenin equivalent circuit…

Answered: 1.44 Consider the circuit shown in…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

You are asked to design a de power supply using a bridge full wave rectifier, as shown in Figure 1.d, to deliver a de voltage of Vo 12 V to a 3 kQ load resistor with a ripple of less than 0.6 Vpp, where Vpp is the peak to peak voltage. The input voltage is a sine wave with frequency of 50 Hz. The diodes have a forward voltage of 0.7 V. i) Calculate the value of smoothing capacitor C. ii) Calculate the rms value of the input voltage, v(t).
In each of the ideal-diode circuits shown below V1 is a 1kHz, 10-V peak sine wave. Sketch the waveform resulting at V0. What are its positive and negative peak values?
....fast and fast..please..
2. Determine the potential across R1. Assume that the zener diode follows a piecewise linear model, with characteristic Zener voltage Vz. Use the simple model for the transistor assuming the usual nominal values. Further, assume that V₁ > V₂. + V1 R2 Q1 NPN D1 Vz R1
You are asked to design a de power supply using a bridge full wave rectifier, as shown in Figure 1.d, to deliver a de voltage of Vo = 12 V to a 3 k2 load resistor with a ripple of less than 0.6 Vpp, where Vpp is the peak to peak voltage. The input voltage is a sine wave with frequency of 50 Hz. The diodes have a forward voltage of 0.7 V. i) Calculate the value of smoothing capacitor C. ii) Calculate the rms value of the input voltage, v(t). Figure 1.d.
Please answer in short I will like but please asap please urgent... Consider the circuit shown in the figure. Assume that each diode has a turn-on voltage of V_gamma = 0.6V. a) Determine R1, R2 and R3 such that, ID1 = 0.2mA, ID2 = 0.3mA and ID3 = 0.5mA. b) Find the voltage across V1, V2 and the current for each of the diodes for, R1 = 10kΩ, R2 = 4kΩ and R3 = 2.2kΩ.
QUESTION 1 Provide an example each for a trivalent and pentavalent element. Describe the doping process of Silicon (Si) to obtain p-type and n-type semiconductor material. a) b) c) Explain forward bias and reverse bias conditions of an ideal p-n junction diode. Sketch the I-V characteristic of Si and Ge diode. Discuss why Si based semiconductor is move favored in production of solid state devices.
Answr all the questions one by one and solve all the unknown values giving all the correct details Let the last digit of the ID = 9
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
Plot the I-V characteristics of a PN junction diode (linear and log scale) for different temperatures and plot the characteristics. Explain the observed behavior.
Question 1 (a) (i) (ii) (iii) Plot the current-voltage characteristic of a p-n diode. In your plot include the forward bias region, reverse bias region and any other important features. Explain what is the major difference between a Zener diode and a p-n diode. Provide one electronic application where a Zener diode is used.
Q1/ a/Draw the output voltage waveform for the bridge rectifier in this figure : 5:1 D Da 120 V ms Dy RL B/ What PIV rating is required for the diodes in a bridge rectifier that produces an average output voltage of 50 V? Q2/ Determine the minimum input voltage required for regulation to be established in the figure. Assume an ideal zener diode with Izx = 1.5 mA and V, = 14 V. lllee 幸

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS

1.44 Consider the circuit shown in Figure PL.44. Determine the diode current lp and diode voltage Vp for (a) V, = 0.6 V and (b) V,0,7 v. +5 V 2 2 ka Figure P1.44 ww ww. ww-