1.39 Consider the diode circuit shown in Figure Pl.39. The diode reverse-saturation current is Is = 10-12 A. Determine the diode current Ip anddiode voltage Vp- +5 V20 kaVo-SVFigure P1.39ww

Fig: Given circuit Given that Is=10-12 A

Answered: 1.39 Consider the diode circuit shown…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A silicon diode has 1 ampere DC of current in biasd mode. What is voltage drop across the diode?
Answr all the questions one by one and solve all the unknown values giving all the correct details Let the last digit of the ID = 9
Zener diodes are special purpose diodes designed to operate in their breakdown regions. Describe the working principle and characteristics of a typical Zener diode found in the market place. The Zener-diode regulator circuit shown below is to be used to provide a stabilised output to the load. The zener diode characteristic is also shown. Find the load voltage and source current if the battery voltage is 20 V, series resistance is 1.4 kohm and load resistance is 6 kohm
Determine the minimum value and the maximumvalue that the series resistor may have in a regulatorcircuit whose output voltage is to be 25 V, whose inputvoltage varies from 35 to 40 V, and whose maximumload current is 75 mA. The Zener diode used in thiscircuit has a maximum current ratingof 250 mA.
Consider a silicon pn junction diode at T 300K. The reverse saturation current is Is = 10-14 A and the ideality factor n = 1. Determine the diode current for a diode voltage of VD = 0.573 V and use that to determine the DC and AC resistance of the diode. RDC = 14.13 k rac = 639 Q RDC = 234 Q2 = rac=8Q RDC = 7.00 KQ rac = 307 Q RDC = 1.43 kQ rac = 58 Q
Design a clipping circuit that will limit the output voltage to 5V when applying an input sinusoidal waveform with a peak value of 10V. Assume available diodes with voltage drop of 0.5V. Sketch the output waveform of the circuit.
diode? Under what circumstances does the output voltage remain constant in a limiter circuit with Zener When does the Z-current Iz begin to flow? Under what circumstances is the limiting effect maintained even under load?
Compared to an ideal PN diode, what are the different characteristics of a practical PN diode? Please list two different characteristics when the diode is reversed biased.
a) Use the diode’s characteristic equation,ID=Is exp(VD/VT), to determine the currentsourceIso that the output voltage is 1.5 V. b) If a load is attached to the output that draws 1 mA, what is the output voltage? c) If the circuit heats up to 40◦C, what is the output voltage without a load?
Q1/ a/Draw the output voltage waveform for the bridge rectifier in this figure : 5:1 D Da 120 V ms Dy RL B/ What PIV rating is required for the diodes in a bridge rectifier that produces an average output voltage of 50 V? Q2/ Determine the minimum input voltage required for regulation to be established in the figure. Assume an ideal zener diode with Izx = 1.5 mA and V, = 14 V. lllee 幸

....fast and fast..please..
Describe in detail how diodes work and their common applications. Design a clipper circuit that eliminates the positive portion of an AC waveform as shown below, leaving only the negative half-cycles to appear on the output. State approximations that you used.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

1.39 Consider the diode circuit shown in Figure Pl.39. The diode reverse- saturation current is Is = 10-12 A. Determine the diode current Ip and diode voltage Vp-