1.30 Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice shown. Knowing that the maximum allowable shearing stress in the glued splice is 620 kPa, determine (a) the largest load P that can be safely applied, (b) the corresponding tensile stress in the splice.

1.30 Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice shown. Knowing that the maximum allowable shearing stress in the glued splice is 620 kPa, determine (a) the largest load P that can be safely applied, (b) the corresponding tensile stress in the splice.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P-3 KN R-2 AN to Figure P1.55 1.55 The force R is the resultant of Pand Q. Determine Q and the angle 0.
Show your complete solution for each problem. Only the final answer in your calculation should be rounded off to two decimal digits. Box your final answer. 1. The increase in the specific internal energy is 33.8 BTU/Ibm in a reciprocating compressor draws 40 lbm/min of air whose density is 0.074 lbm/ft³ and discharge it with a density of 0.311 lbm/ft³. At the suction, the pressure is 18 lb:/in² and discharge 88 lb:/in². If the changed in kinetic energy was neglected, determine the work on the air in horsepower (hp).
Exercise 1.2 1. NASA would like a rocket to accelerate upward at a rate of 125 ft/s². The mass of the rocket is 35,000 Ibm. Determine the upward thrust force, in Ibf, that the rocket engine must produce.
Problem: Determine the pressure in kPa at the following points: a) Point 1 b) Point 2 c) Point A Fluid from Point 1 to Point 2 is mercury (Hg) with Specific Gravity of 13.6. Fluid from Point 2 to Point A is water (H2O). Point 2-A (h=12 cm)
Resolve and draw the diagram of all internal efforts.
1:50 & If a load of 460N was lifted by an effort of 144 N. Then the effort resulted in a 60 m movement. The load moved the distance of 19 m. A.) Calculate the efficiency of the system. B.) Draw a labeled diagram and explain what going on.
1.10 Figure 1.24 shows a special spanner used to tighten screwed components. A torque is applied at the tommy- bar and is transmitted to the pins which engage into holes located into the end of a screwed component. (a) Using the data given in Fig. 1.24 calculate: (i) the diameter D of the shank if the shear stress is not to exceed 50 N/mm², (ii) the stress due to bending in the tommy-bar, (iii) the shear stress in the pins. (b) Why is the tommy-bar a preferred method of applying the torque? 26 26 5 [C.G.] [9.14 mm; 254.6 MN/m²; 39.8 MN/m².] Mechanics of Materials 50N force applied at a distance of 25 mm from both ends of tommy bar Q Fig. 1.24. 05 100
2.2 A metal block is riding a conveyor as it travels through a tunnel type furnace and is subjected to a gradually increasing temperature. With respect to speed of travel, the surrounding temperature of the metal block (i.e. the furnace interior) increases by: T = 50°C + 10°C/min. Where, T furnace temperature in °C. 50°C is the atmospheric temperature at the furnace entry. Draw your best guess of the metal temperature vs. time on a graph for 60 min. from start.
1. Find: a. Type of force needed to cut a huge box into three pieces of small boxes. b. Solve for the force needed to apply in each small box with the given stress. Stress (MPa) Length (cm) Width (cm) Height (cm) First Box 100 20 20 0.10 Second Box 120 20 16 0.04 Third Box 80 20 7 0.15
No. 4 please
4.