1.3 For the Block Diagram below:Y,(s)Y(s)G2G3G.H(s) +a)Find a symbolic expression for the transfer functionY(s)that describes its dynamics.Y,(s)• Use ONLY the following symbolic variables and functions: G; (not G(s)), G2 (not G,(s)), G3 (not G3(s)), G4 (not G(s), H (not H(s))• These symbolic variables and functions are case sensitive (e.g. A a, etc.).• Include mathematical operators (*, I, +, - etc.) as appropriate between variables (e.g. A'cos(b*t) = Acos(bt), etc.)Y(s)Y,(s)%3D

Answered: Image /qna-images/answer/acaf6a90-3229-4dd4-acf9-bbb42cc15992.jpg

1.3 For the Block Diagram below: G Y,(s) Y(s) G2 G3 G4 H(s) a) Find a symbolic expression for the transfer function 5 that describes its dynamics. Y,(s) • Use ONLY the following symbolic variables and functions: G7 (not G,(s), G2 (not G>(s), G3 (not G3(s)), G4 (not G,(s), H (not H(s)) • These symbolic variables and functions are case sensitive (e.g. A= a, etc.). • Include mathematical operators (", I, +, -, etc.) as appropriate between variables (e.g. A'cos(b't) = Acos(bt), etc.) Y(s) Y,(s)

1.3 For the Block Diagram below: G Y,(s) Y(s) G2 G3 G4 H(s) a) Find a symbolic expression for the transfer function 5 that describes its dynamics. Y,(s) • Use ONLY the following symbolic variables and functions: G7 (not G,(s), G2 (not G>(s), G3 (not G3(s)), G4 (not G,(s), H (not H(s)) • These symbolic variables and functions are case sensitive (e.g. A= a, etc.). • Include mathematical operators (", I, +, -, etc.) as appropriate between variables (e.g. A'cos(b't) = Acos(bt), etc.) Y(s) Y,(s)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6. Given the number 0XA0BOCODOE0F0, a. How many bytes for this number b. How many bits for this number c. Store in 8-bit computer with little endian system, and the starting address is 0x123, please show thedata memory map d. Store in 8-bit computer with big endian system, and the starting address is 0x123, please show the data memory map
Q5) An LTI system is characterized by the differential equation below: d² d = y(t)+ = y(t)+16.25y(t) == x(1) dt² dt dt a) Write the characteristic equation. b) Find the characteristic roots. c) Write the form of the zero-input response. d) Write the final zero-input response if yzı(0)=0 and dyzi(0)/dt=2. e) Plot the final zero-input response in Matlab/Octave and select the correct graph on the side: f) What are the characteristic modes for this system? 0 0.5 0 -0.5 0 0 5 (1) 5 (3) 10 10 0.5 -0.5 0.1 0 -0.1 -0.2 Am 0 0 5 (2) 5 (4) 10 10
Consider the system shown in Figure (1). This is a PID control of a second-order plant G(s). For the disturbance input in the absence of the reference input, the closed-loop transfer function is given as below: Ca(s) S D (s) (s + 10) (s² + 4s + 16) Rewrite the transfer function of PID controller in following form: 1 Ge(s)= K₂ (1+: + Tas) Tis R(3) K(as+1)(bs+1) PID controller D(s) Figure (1) +3.68+9 Plant G(s) C(s)
Q4) An LTI system is characterized by the differential equation below: d² = y(t) + 5 = y(t)+6y(t) = x(t) dt2 dt a) Write the characteristic equation. b) Find the characteristic roots. c) Write the form of the zero-input response. d) Write the final zero-input response if yzı(0)=2 and dyzi(0)/dt=-1. e) Plot the final zero-input response in Matlab/Octave and select the correct graph on the side: f) What are the characteristic modes for this system? 1.5 1 0.5 0 -0.5 1 2 3 4 (1) 0.5 0 -0.5 -1 -1.5 (2) 4 01234 (3) 1.5 0.5 234 (4)
R(s) G₁(s) G₂(s) G4(S) G6(s) G3(s) G5(s) - H₁(s) G7(s) b) Find the equivalent transfer function of this system. -H₂(s) C(s) - H3(s) a) Convert the signal flow graph into an equivalent block diagram, no simplification needed
Q2: Find the transfer function C(s)/R₂(s) for the block diagram shown in Fig.(2) below, using block diagram reduction method. H3 R₁(s) G₁ G₂ H₁ R₂ (s) H₂ G3 → C(s)
Draw the block diagram of A
B/ Apply Mason's Rule to calculate the transfer function of the system represented by following Signal Flow Graph R(S) G6 G1 -H3 -H1 G7 G2 -H4 -H2 G8 G3 G5 G9 G4 Fig. 2 Y(S)
All initial conditions are assumed to be zero for the electrical circuit given in the figure below. According to the given;a) Obtain the transfer function V2(S)/V1(S).b) Calculate the damping ratio and natural frequency value in terms of R, L, C parameters for the expression you found in option A.c) For V2(t), a maximum of 25% overshoot is required. In this case, what should be the R value for L=10mH, C=4MikroF.
Electrical Engineering Major. Course: EE350 ( System Dynamics and control ).
Needs Complete solution with 100 % accuracy.
Please answer in typing format please ASAP for the like please Please ????