1.22. A plane wall 0.15 cm thick, of a homogeneous material with k = 0.40 W/m- K, has steady and uniform temperatures T,- 20 °C and T- 70 C (sce Fig 1-6). Determine the heat transfer rate in the positive r-direction per square meter of surface area Ans -133 W/m

1.22. A plane wall 0.15 cm thick, of a homogeneous material with k = 0.40 W/m- K, has steady and uniform temperatures T,- 20 °C and T- 70 C (sce Fig 1-6). Determine the heat transfer rate in the positive r-direction per square meter of surface area Ans -133 W/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A wall of length "L" m and height "H" m is made from a thick bricklayer of 29 cm with thermal conductivity of 0.5 W/mK is subjected to heat transfer due to the outside temperature as 43 oC and inside temperature 28 oC. If the energy loss is 11427 kJ in 9 hours. Determine the Heat transfer rate, Surface Area and Length and Height of the wall, if L = 1.5 H. Solution: i) Heat Transfer Rate (in Joule/Sec) = ii) Surface Area of the Wall (in m2) = iii) Height of the Wall (H in m) = iv) Length of the Wall (L in m) =
i need the answer quickly
Q.3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. (10 Pts)
Please solve this question in thermodynamics
A furnace wall consists of 2 ft of brick . The brick has athermal conductivity of 0.6 Btu/ hr sq ft ( ° F /ft), a specific heat of0.2 Btu/ lb ° F, and a density of 110 lb/cu ft. The temperature atthe inside surface of the wall is 1100 ° F , and at the outside surface,200 ° F .(a) Calculate the thermal diffusivity of the brick .(b) Calculate the heat loss per hour through a wall 10 ft high and10 ft long(c ) Calculate
This question requires the use of the conduction charts given in the appendix at the end of this paper. A wooden sphere of diameter 5 cm is initially at a uniform temperature of 21 °C. Its surface temperature is suddenly raised to 83 °C. The thermal conductivity and thermal diffusivity of the wood are 0.15 W/m K and 0.82 x 10-7 m2/s, respectively. a) Calculate the temperature 2 cm beneath the surface of the sphere 30 min after the sudden increase in temperature. b) Calculate the energy gained by the sphere during this time.
The wall of a furnace comprises three layers as shown in the figuie. The first layer is tery (whose maximum allowable temperature is 1400°C) while the second laver is Tracto:y Chose maximum allowable temperature is 1093°C). The third layer is a plate of 6 35 od thermal contact. Steet plare To 6.35x3 45A 1370 C Concerntiation veluciy 37.8 C mass Siynes Figure. Layers in a composite furnace wall. e temperature To on the inside of the refractory is 1370°C, while the temperature T; on the side of the steel plate is 37.8° The heat loss through the furnace HnIlisexpectet tobe
The inner and outer surfaces of a 1-m by 1-m wall of thickness 100 mm and thermal conductivity 10 W/m. C are maintained at temperatures of 35 C and 15 C, respectively. Determine the heat rate by conduction. Select one: a. 2 kW b. 2 MW c. 20000 W
Q1) A polished metal pipe (8 cm) owtside diameter and 350 K temperature at the outer surface is exposed to ambient conditions at 285 K temperature. The emissivity of the surface is 0.3 and the convection coefficient of heat transfer is 13.5 Wim2-deg. What would be the overall coefficient of heat transfer by the combined mode of convection and radiation” Q2 find the pressure point (1) if the amospheric pressure is(70kpajihl =0 2,h2=0.4,h3=0. ‘)(p. =13600kg/m3. poil=850kg/m3)
Consider a large plane wali of thickness L03 m thermal conductivity k25 /m K, end surfece aree A 12 m The left side of the well ot x=O is subjected to a net heat flux of go760 W/m while the temperature at that surfece is measured to be T 80°C Assuming constant thermal conductivity and no heat generation in the wall, ovaluate the temperature of the right surface of the wall at xEL The temperature of the right surfaoe of the wall at x Lis
A metal plate has a surface area of 2 m², thickness 100 mm and a thermal conductivity of 200 W/mK. The thermal resistance of the plate in (K/W) is
Q) The temperature of a heated plate is 88°C which is cooled by using pin-fins having a length of 5-cm, diameter of 1-cm, and thermal conductivity of (k=201 W/m-°C). The number of pins is (N=1800) and the temperature of the atmosphere is 10°C, while the convection heat transfer coefficient on the surfaces is 37 W/m2.°C. Assuming steady one-dimensional heat transfer along the fin and taking the nodal spacing to be 2.5-cm, determine (a) the temperature at the nodes along the fins, (b) the heat transfer rate from a single fin, (c) the heat transfer rate from all fins, and (d) the overall heat transfer rate from the heated plate which has dimensions of 0.6-m x 0.5-m with the fins.