Simple stress and Strain 1.1 (A). A 25 mm square-cross-section bar of length 300 mm carries an axial compressive load of 50 kN.Determine the stress set up in the bar and its change of length when the load is applied. For the bar materialE = 200 GN/m2.[80 MN/m²; 0.12 mm.]

Answered: Image /qna-images/answer/9cbd329e-ca24-451d-afef-4d1e239a6344.jpg

1.1 (A). A 25 mm square-cross-section bar of length 300 mm carries an axial compressive load of 50kN. etermine the stress set up in the bar and its change of length when the load is applied. For the bar material = 200 GN/m². [80 MN/m²; 0.12 mm.]

1.1 (A). A 25 mm square-cross-section bar of length 300 mm carries an axial compressive load of 50kN. etermine the stress set up in the bar and its change of length when the load is applied. For the bar material = 200 GN/m². [80 MN/m²; 0.12 mm.]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: n kn

A: given: ratio of linear strain and laterial strain known as?

Q: The von mises criterion is to be used for yield predicitons of a given metal. Under plane strain…

A: The Von Mises criterion is to be used for yield predictions of a given metal.Objectives:Under plane…

Q: d) If a material of a component has a youngs modulus of elasticity of 800 GPa, what strain will be…

A: Given data: E=800 GPaσ=5 MPa Need to determine the strain.

Q: Which material has the greatest UTS?

A: The ultimate tensile stress is the maximum stress in the material corresponding to the strain.

Q: What is Circumferential Stress?

A: Circumferential Stress When pressure inside thin pressure vessel exceeds it exerts force from inside…

Q: Differentiate between normal strain measures and sheer strain measures?

A: Normal Strain: The deformation caused in normal strain is due to normal forces such as tension or…

Q: What are the units of measurement for stress?

A: Step-1 Stress is basically the measure of an external force which acts over the cross sectional area…

Q: How is the torsion test performed to determine the material’s ultimate shear stress?

A: A torsion test is a destructive type of testing used to find the properties of specimen under stress…

Q: What does stress analysis require to determine the maximum stress?

A: Stress analysis requires Material properties.

Q: The following data are obtained from a tensile test of a coppe - The load at the yield point is 151…

Q: How is normal strain measured?

A: As we know that strain is a change in length over original length.

Q: What does the region of strain hardening cause?

A: The working of the metals below their recrystallisation temperature is known as cold working…

Q: If a material of component has a tensile modulus elasticity of 300 GPa, what strain will be produced…

Q: What is the unit of strain?

Q: In structures deformation or strain may be the result of ___________. Choose all that apply…

A: Introduction: Deformation is the amount an object is stretched, while strain is the ratio of…

Q: Fracture occurs when the stress is greater than the ultimate tensile strength Select one: True False

A: given statement : Fracture occurs when the stress is greater than the ultimate tensile strength

Q: Why would engineers use Vickers Hardness testing (HV) over Brinell Testing for hardened tool steel…

A: Hardness is the property of the material that can be understand as the resistance to scratch and…

Q: If the area under the stress and strain curve is more then it is concluded that the material has…

A: The area under stress - strain curve represents the energy required or stored in the material before…

Q: What is the permanent strain?

A: Strain: When a force is applied to any system, they deform based on the applied force. The…

Q: 8 Draw a Stress-Strain diagram for steel and label stresses and the regions

Q: The strain at failure is very small for __________ Select one: a. Aluminum b. Copper c. Mild Steel…

A: We have made an approximate stress-strain graph for your better understanding.

Q: What is the tensile stress?

A: When there is loading over a member in the direction of its axis, then stress produced under such…

Q: How is the Strain actually measured?

A: Before explaining the measurement of strain, let's first understand the strain. Strain is basically…

Q: 27d) If a material of a component has a youngs modulus of elasticity of 500 GPa, what strain will…

Q: Which of these cast iron would allow the greatest amount of plastic deformation before fracture. O…

A: Nodular or ductile cast iron has its graphite in the form of very tiny nodules with the graphite in…

Q: Luestion One In a tensile test, material mechanical properties are determined by relating…

A: Solution is attached below:

Q: 1) Explain the main characteristic of each curve in one or two sentences in the following…

A: 1) The curve d is for the brittle material as there is no plastic deformation in the material. The…

Q: The laboratory mechanism used to test the fatigue life of materials is Select one a. A rotating…

A: The fatigue test using the rotating-beam fatigue tester is the oldest method to determine the…

Q: If the engineering stress is 100 MPa, and the corresponding engineering strain is 0.0015, what is…

A: Given Data: Engineering Stress σE=100 Mpa Engineering Strain ε=0.0015

Q: How are Engineering stress and strain calculated?

A: Engineering stress is also known as the nominal stress, defined as the ratio of applied load to the…

Q: The true stress (in MPa) versus true strain relationship for a metal is given by O = 1020 e0.4 The…

A: As per question given data σ=1020∈0.4∈=0.4initial area A =100mm^2 we have to determine the cross…

Q: What are the principal strains?

A: Principal Strain: Maximum and minimum normal strain possible for a specific point on a structural…

Q: Which of the following statement is correct? (a) The stress is the pressure per unit area. (b)…

A: Option d is correct: Stress is directly proportional to strain within elastic limit.

Q: Which of the following stress strain curve shows an elastic behaviour to very high strain rate O a.…

Question

Simple stress and Strain

1.1 (A). A 25 mm square-cross-section bar of length 300 mm carries an axial compressive load of 50 kN.
Determine the stress set up in the bar and its change of length when the load is applied. For the bar material
E = 200 GN/m2.
[80 MN/m²; 0.12 mm.]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

New projections can illustrate the possible presence of angular strain. a True b False
What is Residual Stress?
In the Tensile experiment, the function of a load cell is to: Select one: a. Measure the applied force. b. Measure the applied strain. c. Measure the applied stress. d. Measure the specimen elongation.
What are the experimental techniques used to measure the strain?
Which one of the following, in some form or another, causes all other choices? Shear stress Force Normal Stress Bearing Stress
An example of two types of stress?
What is the concept of Strain?
In drawing process, compressive forces are used to reduce the cross section of the workpiece. Select one: True False
What is Normal Stress?
What is process when stress causes a material to strain past the elastic limit and material has a permanent deformation? Stress Ductile deformation Fault Strain Elastic deformation