Do it soon like is ready 1. Write a MIPS Assembly program to ADD the numbers: 1, 2, 3, 4, 5, 6, 7, 8 (as inex-1)• Use ONLY the instructions: add and liThe result of the addition (in decimal) should be in register: $t12. Write a MIPS Assembly program to ADD the numbers: 1, 2, 3, 4, 5, 6, 7, 8 (as inex-2). Use ONLY the instructions: addi and liThe result of the addition (in decimal) should be in register: $t1

Below are the program that are written in subrotuine..

1. Write a MIPS Assembly program to ADD the numbers: 1, 2, 3, 4, 5, 6, 7, 8 (as in ex-1) Use ONLY the instructions: add and li The result of the addition (in decimal) should be in register: St1 2. Write a MIPS Assembly program to ADD the numbers: 1, 2, 3, 4, 5, 6, 7, 8 (as in ex-2) Use ONLY the instructions: addi and li . The result of the addition (in decimal) should be in register: St1

1. Write a MIPS Assembly program to ADD the numbers: 1, 2, 3, 4, 5, 6, 7, 8 (as in ex-1) Use ONLY the instructions: add and li The result of the addition (in decimal) should be in register: St1 2. Write a MIPS Assembly program to ADD the numbers: 1, 2, 3, 4, 5, 6, 7, 8 (as in ex-2) Use ONLY the instructions: addi and li . The result of the addition (in decimal) should be in register: St1

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter6: System Integration And Performance

Section: Chapter Questions

Problem 19VE

See similar textbooks

Similar questions

1. Write a MIPS Assembly program to ADD the numbers: 1, 2, 3, 4, 5, 6, 7, 8 (as in ex-1) . Use ONLY the instructions: add and li The result of the addition (in decimal) should be in register: St1
For the following MIPS assembly instructions what is the corresponding C statement? Assume that variables f,g,h,i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. Add comments for each line to describe what each instruction does. addi $t0, $s6, 4 # $t0 = &A+4 = &A[1] add $t1, $s6, $zero # sw $t1, 0($t0) # lw $t0, 0($t0) # add $s0, $t1, $t0 #
For the RISC-V assembly instructions below, what is the corresponding C statement? Assume that the variables f, g, h, i, and 3 are assigned to registers x5, x6, x7, x28, and x29, respectively. Assume that the base address of the arrays A and B are in registers x10 and 11, respectively. sub x30, x28, x29 slli x30, x30, 2 add x3, x30, x10 add x4, x30, x11 Iw x30, 0(x3) 1w x31, 0(x4) add x30, x30, x31 sw x30, 16 (x11)
3
1. The nor & nand instructions are not part of the RISC-V instruction set because the same functionality can be implemented using existing instructions. Write RISCV code that performs a nor operation on registers x8 and x 9 and places the result in register x10. Write RISCV code that performs a nand operation on registers x5 and x6 and places the result in register x7
..
Show the MIPS assembly codes to implement each of the following: Photo attached below for your reference. Thanks!
Assume that registers $s0 and $s1 hold the values 0x80000000 and 0xD0000000, respectively. What is the value of $t0 for the following MIPS assembly code? Is the result in $t0 the desired result, or has there been overflow? add $t0, $s0, $s1 Is this overflow or underflow? Please explain
Computer architecture. Please make sure of the answer
20 LDA 50 21 SUB 51 50 100 51 200 Choose the contents of the registers: PC, MAR, MDR, IR, A at the end of fetch-execute cycle for instruction 20: PC MAR MDR IR A
Based on the instruction set below, determine if the given assembly statement is valid or not. Write valid if statement is valid. Write invalid if statement is not valid. Note A, B, and C are registers X, Y, and Z are memory locations 1. MOV Y.C 2. ADD B,C 3. SUB A,X 4. INC X 5. MVI X,20 For the instruction set below , D must be a register; S is a register or a memory location 3. MOV D,S ;DES 4. ADD D,S ; DE D+S 5. SUB D,S ;DE D-S 6. MVI D, I where I is an immediate data 7. LDA X ;AE [X] where X is a memory location 8. STA X 9. INC D DED+1
For the MIPS assembly instructions below, what is the corresponding C++ statement? Assume that the base address of arrays A and B are in registers $s6 and $57, respectively. Iw $s0, 0($s6) addi $s0, $s0, 5 Iw $s1, 4($s6) add $$0, $s0, $s1 Iw $1, 8($s6) add $s0, $s0, $s1 sw $s0, 0($s7) O B[O] = A[5] O A[O] = B[0] + B[1] + B[2] O B[O] = A[0] + A[1] + A[2] + 5 B[0] = A[O] + A[4] + A[8]