1. Which of the following are the three main components of a simple circuit?B. battery, wire, switch C. battery,bulb,wireA. battery,bulb, fuseD. battery,fuse,switch"For nos. 2 and 3 There are four light bulbs connected in parallel as shown in the circuit diagram below.$2. Where would you put a switch that would turn all the light bulbs off? A. EtB. CC. BD. AD. A3. Where would you put a switch that would turn one light bulb off and leave four light bulbs on? A. E. B. C C. B*For nos. 4-5, study the circuit diagrams below.000Circuit ACircuit B4. Which circuit is wired in series?5. Which circuit is wired in parallel?6. What is the unit of measurement to measure the opposition to current flow in an electrical circuit?A. AmpereB. OhmC. VoltageD. Watt7. The circuit with higher resistance will allow less charge to flow.A. TrueB. FalseC. SometimesD. Not enough information8. What is the unit of measurement to measure the movementof charge (electron) through a wire?C. CurrentD. AmpereA. VoltB. Ohm9. The current-voltage relationship can be represented through agraph.B. linearC. non-linear D. parabolicA. hyperbola10. Which resistor should I connect to a circuit to get the least amount of current?C. 20-Q resistor D. 25-0 resistorA. 10-Q resistor B. 18-Q resistor1. A 10-ohm resistor is powered by a 5-V battery. What is the resulting current?A. 0.5 AB. 10 AC. 15 AD. 50 A2. The resistance in a carbon filament lamp...A. decreasesB. doubledC. increasesIf you increase the voltage across a resistor, what will happen to the current? The current willRECORD. remains the sameD. stay the same.

Given: Five electric bulbs are connected in parallel with battery.

1. Which of the following are the three main components of a simple circuit? A. battery,bulb, fuse B. battery, wire, switch C. battery,bulb,wire D. battery,fuse,switch "For nos. 2 and 3 There are four light bulbs connected in parallel as shown in the circuit diagram below. $ 2. Where would you put a switch that would turn all the light bulbs off? A. E B. C C. B D. A 3. Where would you put a switch that would turn one light bulb off and leave four light bulbs on? A. E. B. C C. B D. A

1. Which of the following are the three main components of a simple circuit? A. battery,bulb, fuse B. battery, wire, switch C. battery,bulb,wire D. battery,fuse,switch "For nos. 2 and 3 There are four light bulbs connected in parallel as shown in the circuit diagram below. $ 2. Where would you put a switch that would turn all the light bulbs off? A. E B. C C. B D. A 3. Where would you put a switch that would turn one light bulb off and leave four light bulbs on? A. E. B. C C. B D. A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Answer question 13 to 15 please.
24 Voltmeter shows an error of 13 V for 356 V reading, the percentage accuracy of voltmeter is_______ % a. 3.65 b. 0.04 c. 13.00 d. 0.27
10 ) Voltmeter shows an error of 8 V for 379 V reading, the percentage accuracy of voltmeter is_______ % a. 0.02 b. 0.47 c. 8.00 d. 2.11
You were required to create a circuit consisting of a wire, a battery, a bulb, and a switch. After the construction, you were tasked to measure the voltage, current, and resistance. How are you going to perform the task in order for you to measure these electrical quantities?
A consumer has a work area that he wishes to illuminate with single 80W, 220V tungsten fitting. The existing light points, which are to be removed are controlled by a single gang 10A switch. This switch is to remain in the design. How many light fittings will the switch support. A-Current consumed by one fitting is B-The switch must carry the current of C-Number of fitting supported by the switch is
PLEASE ANSWER THE QUESTIONS ATTACHED BELOW :)
) Determine the values and tolerances of resistors having the following colour coding; i) Blue-Grey-Orange-Red ii) Yellow-Violet-Gold iii) Blue-White-Black-Black-Gold Major Topic 4 Colour Coding of Resistors
Two resistors: Brown Black Red and Yellow Violet Red are configured as shown above. What would be the measured resistance between the top and bottom connections? ohms Put in numbers and engineering prefixes only. Round to 1 decimal p (x.x). Use engineering notation but leave out the word "ohms". It is already written for you. If 5 volts is applied between the top and bottom connection, what would be the measured tota current through the resistors: Br BI Red resistor A Use engineering notation. No decimal places. YV Red resistor : CHoose the word that represents the current through this second resistor: same/larger/smaller ?
Please answer all subparts for like either dislike.. Please Answer
please answer
For a basic electrical circuit what 3 components do you need
please help me with these questions on resistors.