1. When sampling a continuous signal, if the recording time of the signal remains unchanged, the higher the sampling frequency, the (). A) The greater the leakage error C) More sampling points 2. The quality factor which describes the filter's ability to discriminate adjacent frequency components of a signal is (). A) Cut-off frequency B) Bandwidth B) The more serious the frequency aliasing D) The lower the frequency domain resolution C) Quality factor D) Ripple amplitude 3. For a damped system, only the () resonant frequency is equal to the natural frequency of the system. A) Displacement B) Speed C) Acceleration D) Displacement and velocity 4. It's wrong to say that the film is about compensation (Q. A) The performance parameters of the compensation piece and the working piece are exactly the same B) The material of the compensation sheet is the same as that of the tested part C) The compensation piece and the working piece shall be placed as close as possible and must be pasted on the measured object. D) The working piece and compensation piece are connected to the adjacent bridge arm 5. There are () working bridge arms in half bridges. A) one B) two C) three D) four

1. When sampling a continuous signal, if the recording time of the signal remains unchanged, the higher the sampling frequency, the (). A) The greater the leakage error C) More sampling points 2. The quality factor which describes the filter's ability to discriminate adjacent frequency components of a signal is (). A) Cut-off frequency B) Bandwidth B) The more serious the frequency aliasing D) The lower the frequency domain resolution C) Quality factor D) Ripple amplitude 3. For a damped system, only the () resonant frequency is equal to the natural frequency of the system. A) Displacement B) Speed C) Acceleration D) Displacement and velocity 4. It's wrong to say that the film is about compensation (Q. A) The performance parameters of the compensation piece and the working piece are exactly the same B) The material of the compensation sheet is the same as that of the tested part C) The compensation piece and the working piece shall be placed as close as possible and must be pasted on the measured object. D) The working piece and compensation piece are connected to the adjacent bridge arm 5. There are () working bridge arms in half bridges. A) one B) two C) three D) four

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An ideal boost converter is utilized in designing a PV storage system. The boost converter is operating at the boundary layer between the continuos conduction mode and discontinuous conduction mode. Design the mathematical model of the switching frequency for this boost converter in terms of load, duty cycle and inductance under the above operating conditions.
Q5: An electron drops from specific energy level to ground state (n=1) in hydrogen atom. The energy difference between these two levels is 12.75 eV. Calculate the initial state of the electron and 2 of the emitted radiation. (Ans: n¡ = 4, 972.54 Å) %3D
Consider two types of digital filters: Butterworth and Elliptic. (c) Comment on the difference between your two designed filters (incl. comparison of filter order, transition band, ripple and phase response).
He (e tw) -27 27 The frequency-omplitude graph of discrete time low pass filter is given above. Based on this graph, find the time domain equivalent of a high-pass fiter in the time doman by inverse fourter transformartion.
Draw the circuit diagrams of a first and a second order band pass filter and indicate its lower and upper cut off frequencies. Do the same for band stop filter. thanks in advance! ..
-3dB point in frequency response of an active filter corresponds to A. absolute value negative 3dB of gain B. decrement of 3dB from maximum gain C. minimum gain attained D. minus 3dB of average gain value
Q.2:- a) Explain what a band-pass filter is, and how it differs from either a low-pass or a high-pass filter circuit. Also, explain what a hand-stop filter is, and draw Bode plots representative of both band-pass and band-stop filter types. b) What is the purpose (ll) of the parity bit during data transmission?
I need the answer as soon as possible
5. According to the relationship between matching filter transmission function and input determination signal in white noise background, briefly describe the principle of matching filter in white noise background ; briefly describe the reason why the matching filter is adaptive for signals with similar waveform but different amplitude and delay parameters.
State the names and draw the response curves for the FOUR (4) major filter types.
urgent please
CR active filters find extensive use in communications and instrumentation measurements. a) By considering how the capacitor impedance in Figure 1 varies with frequency, explain if the circuit in Figure 1 acts as a low-pass or high-pass filter. p) Derive the closed-loop gain for the case of very high frequencies. c) Draw a graph that shows the frequency response of the CR active high-pass filter. The y-axis should correspond to gain in dBs and the x-axis to frequency. Make sure that you clearly indicate the 3 dB point and the equation that describes the relationship between w and CinRin at the cut-off frequency. Cin Rin A Vin Vout Figure 1