1. When connected to the source, the 60HZ power line supplies current of 10<30° to the load which generates a voltage of 1500rms<20° across it at a lagging power factor of 0.85. By adding a “shunt capacitor" into the circuit, we can improve the power factor at the load side to unity. Find out what will be the ideal value of the "shunt capacitance". MUST draw appropriate power triangles with proper labeling to explain your answer. Show all steps and workings. IL + Source Load VL

1. When connected to the source, the 60HZ power line supplies current of 10<30° to the load which generates a voltage of 1500rms<20° across it at a lagging power factor of 0.85. By adding a “shunt capacitor" into the circuit, we can improve the power factor at the load side to unity. Find out what will be the ideal value of the "shunt capacitance". MUST draw appropriate power triangles with proper labeling to explain your answer. Show all steps and workings. IL + Source Load VL

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The single phase AC sinusoidal voltage then the rms value of the voltage v is .........
V1 ZT Z2 V2 V3 Z5 Z3 Z4 Figure 18.4 See Figure 18.4. In a general bridge circuit such as this, what condition will result in a balanced bridge? Z1Z4 = Z2Z3 Z3 = Z4 O ZĄZ3 = Z2Z4 O Z1Z2 = Z3Z4
What is the value of capacitance that needs to be connected in a parallel configuration to the load in order to correct the pf source to 0.94 lagging. Frequency f= 129 Hz
Two loads are connected in parallel to a 2000 V(rms) 50Hz source. one of the loads Each of them has 500KVAR reactive power and 0.6 reverse power factor. Other load 300KW since it has absorbing power and 100KVAR dissipating power a) Draw the equivalent circuit of the system b) Find the common power factor of the system c) In order for the power factor to be 0.98 back, the capacitor to be connected in parallel with the loads find its value d) The magnitude of the current drawn from the source is measured before and after the capacitor is connected Find and compare for the next cases. Not. Solve this question in detail step by step and explain your requests in detail
A sinusoidal current of 5 Arms is flowing through a series combination of a resistor and Inductor. The value of R is 45 ohms and that of the inductance is 15 mH and a frequency of 60 Hz. Find the magnitude and the phase angle of the voltage across the combination. (Hint: you can use phasor diagram). Select one: a. [V]=28.89, angle=9.39 b. IV]=25.60, angle367.00 c. [V]=128.01, angle3D10.18 d. IVl=226.77, angle=D7.16
Another name for reactive power is?
In the figure below, all impedances are in ohms, all voltages are in volts and currents in Amperes. Both sources operate at 60 Hz. X, = 200 n X, = 600 n 80 sin (wt + T/2) x, = 600 2 0.2 ain wt Determine the time dependent current i (A) due to the current Choose... source Determine the time dependent current (A) flowing through the inductance with a Choose... reactance of 200 Ohms due to the current source Determine the time dependent current i (A) due to the voltage Choose... source Choose... Determine the total effective current (A) flowing through the Choose... inductance with a reactance of 200 Ohms
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. a = 50° T1 50 2 ot Vs = 300 sin 100rt T2 ot