1. What is the function of power supply test inautomotive electircal diagnosis?2. What is the function of positive circuit andground connection test in automotive electircaldiagnosis?3. What is the function of motor voltage droptest in automotive electircal diagnosis?

Since you have asked multiple questions, we will solve the first question for you. If you want any…

Answered: 1. What is the function of power supply…

Engineering

Electrical Engineering

1. What is the function of power supply test in automotive electircal diagnosis?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

The voltage drop at brush- commutator contact is variable (1-2V) .and dependent of armature current True O False O
A Flyback converter (for questions 1-3) shown below has the following parameters. Vin-100V, Vo-20v, Po-40W, D-0.25, Fsw-250kHz 1. What is the turns ratio N1:N2 between the primary side winding and the secondary side winding? A. NI: N2 - 5: 3 B. NI: N2 - 3:5 C. NI: N2- 5:2 D. None of the above
Q4/ Chose the correct answer for the following 1. In BLDC motor field winding is kept on a) Stator b) Rotor c) Can be placed anywhere d) Absent 2. By electronic circuitry BLDC can be controlled for both constant and variable torque operation. a) True b) False 3. In medical fields which DC motor is widely used? a) PMDC b) BLDC 4. Construction of BLDC is exactly similar to the a) Conventional DC motor c) Permanent magnet synchronous motor b) Induction motor 5. Typical brushless motor doesn't have a) Commutator b) Permanent magnet 6. The sensor most commonly used in the BLDC motor is a) Thermo Sensor b) Relay Sensor c) Brushed DC motor d) Cannot be determined d) Totally different construction c) Electronic controller d) Fixed armature c) Hall Sensor d) Power Sensor
help me in these questions pls write the questions with the and by (Computer) 1-Which of the following statements INCORRECTLY explain the label in the figure about LVDT working principles? a. Secondary coils are connected in series in such a way that their output is opposing each other. b. Constant DC voltage input to primary coil. c. Displacement moves ferrous rod from central position. d. The difference of the output voltage between the two secondary voltage.==========2- Explain the working principle of the measurement system in the figure below.i. Force input that is supplied to the sensor is processed to give the response in the form of raw output signal.ii. Signal conditioner manipulated the weak signal to give a conditioned input.iii. Analog or digital indicator display the unit that gives output reading of quantity being measured.iv. Measured value is compared with the input value for further action. a. ii, iii and iv only. b. i, ii and iv only. c. i, ii and…
9-In a the shunt field winding is connected in parallel with the armature winding only. Ish Series . Field EJR Shunt Rsh Rse Field 10-The consist of and 11- E = (V – IaRa ) then N = LOAD
Please answer only handwritten accepted...I will like that solution.. Please clear handwriting.. Please.. .
f) Write the mathematic expresion for the Series Injected Voltage in UPFC for the following control cases: a) Voltage Regulation: b) Impeadance Compensation: c) Phase Shifter:
For which reasons its not possible to develop rated voltage of d.c shuntgenerator, both in unloaded and loaded conditions?
Q- Select the correct answer: a- The high concentration of holes and electrons in the central junction of a thyristor decreases by the process of ................ during off transient period with a time tar. 1- Forced commutation, 2- Phase commutation, 3- Load commutation, 4- Reverse bias commutation, 5- None of previous. Power Electronics b- The non-trigger voltage of a thyristor is.............. 1- VBO, 2- VBn, 3- VGn, 4- VGD, 5- None of previous. is the limiting positive anode voltage above which thyristor may be damage. 1- PRV, 2- PFV, 3- PAV, 4- PAK, 5- None of previous. C- d- The ripple frequency in the output voltage of single-phase half-controlled bridge AC/DC converter is when a > 60°. 1- 3f, 2-6f, 3- 2f, 4- f, 5- None of previous. ********* e- The integrator in the firing circuit of 1-phase bridge AC/DC converter is necessary to have firing angle range. 1-0-90°, 2-0-120°, 3-0-180°, 4-0-360°, 5- None of previous. f The harmonic contents in an inverter can be reduced through…
can someone help me out with this question 5 and pls explain clearly, tq
A Flyback converter (for questions 1-3) shown below has the following parameters. Vin=100V, Vo=20v, Po=40W, D=0.25, Fsw=250kHz iin i out in 1. What is the turns ratio N1:N2 between the primary side winding and the secondary side winding? A. Ν1: N25:3 B. N1: N2 = 3:5 C. N1: N2= 5:2 D. None of the above %3D 2. What is the maximum voltage on the power switch? A. 120V В. 133V С. 100V D. None of the above 3. What is the maximum voltage on the diode? Α. 40V В. 133V C. 80V D. None of the above 4. The magnetizing inductor at the primary side winding is 100uH, what is the peak current in the power switch? Α. 1.8Α В. 1.6A С. 2.1A D. None of the above
i need the answer quickly