Answered: 1. What are the applications for…

1. What are the applications for stripline and microstrip transmission lines? 2. Give 2 examples of characteristic impedance application for each stripline and microstrip transmission lines.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.29P: Consider three ideal single-phase transformers (with a voltage gain of ) put together as ...

See similar textbooks

Similar questions

To convert a per-unit impedance from old to new base values, the equation to be used is Zp.u.new=Zp.u.old(VbaseoldVbasenew)2(SbasenewSbaseold)Zp.u.new=Zp.u.old(VbaseoldVbasenew)2(SbasenewSbaseold)Zp.u.new=Zp.u.old(VbaseoldVbasenew)2(SbasenewSbaseold)
Describe the principles and benefits of High Voltage Direct Current (HVDC) transmission systems, and when are they preferred over traditional AC transmission systems?
Please provide Handwritten answer
In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 15kV and that across the next unit is 12kV. Estimate: ratio of mutual to self-capacitance i. the bus-bar voltage of the substation. Efficiency across the string of insulators ii. iii.
Analyse several voltage and current situations in different loading scenarios in a simplified radial (transformer to consumption) medium-voltage power system example. There are only 2 nodes in the 35 kV line – node 0 from the 110/35 kV and node 1 with one consumer. The physical characteristics of the line and the loading scenarios are individualized for each student – please see the attached file Excel “WM9P3 Task1 data” for your particular data set. Briefly reflect on the complexity of the calculations for known input or output voltage, as well as for fixed or voltage-dependent consumption in this simple power system model. Analyse and discuss the sensitivity of the voltage drop [in % of amplitude and the degrees of phase] with respect to the current level [in %] and to the power factor.
For the system in Figure 4 with given generation and load dispatch determine the voltages after two itterations of Gauss-Seidel method. Assume the initial voltage to be 1.01 at angle of 0◦ pu at bus 1, 1.015 at angle of 0◦ pu at bus 2, and 1.0 at angle of 0◦ pu at bus 3. All line impedances are in per unit on a common base, and charging is neglected. Take base power of 100 MVA.
Describe the concept of FACTS (Flexible AC Transmission Systems) devices and their applications in enhancing power system performance.
X=2 Y=8
Some electricians do not bother to calculate the minimum size of neutral service conductor. They size the minimum ungrounded conductor size and then use this information to determine the minimum neutral conductor size. Explain how they determine the minimum neutral size using the minimum ungrounded conductor siz
Q5: Three identical transformers are needed to connect a 6-kVA, 120-V, three- phase load to a 4800-V, three-phase trans mission line. For a Y/A connection, determine (a) the power rating, (b) the voltage rating, (c) the current rating of each transformer and (d) What is the a-ratio? Answer: (a) 2 kVA, (b) 2771.28/120 V, (c) 721.69 mA/16.67 A, (d) 23.09
please solve this 2 question handwritten step by step solution to make me understanding it well thank you
How do FACTS (Flexible Alternating Current Transmission Systems) devices impact power system control and stability?