1. Water flows at a rate of 0.020 m3/s from reservoir A to reservoir B through three concrete pipes connected in series, as shown. Find the difference in water surface elevation in the reservoirs. Use f = 0.026 for all pipes. Neglect minor losses. Water 1600 m, 200-mm diameter 1000 m, 160-mm diameter 850 m, 180-mm diameter Water

1. Water flows at a rate of 0.020 m3/s from reservoir A to reservoir B through three concrete pipes connected in series, as shown. Find the difference in water surface elevation in the reservoirs. Use f = 0.026 for all pipes. Neglect minor losses. Water 1600 m, 200-mm diameter 1000 m, 160-mm diameter 850 m, 180-mm diameter Water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two pipes in a series have a flow rate of 50 L/s. The pipe upstream is 300 mm and reduced downstream to 150 mm. Determine the velocities for both diameters in m/s. Consider the centerline of the pipes along a horizontal datum reference. Ignore losses.
In a hydraulic system, the power is measured as 52 X 10-2 Kilo joules per seconds and pressure is given 320.6 x10-3 N/m2 .Find the flowrate of the hydraulic system.
answer fast
Reservoir A (Elevation 300m) supplies water to reservoir B (Elevation 180m) thru a 450 mm ductile iron pipe. A turbine is installed in the same level with Reservoir B. The total system flow is 350 gpm determine the the output power in Hp if the turbine is 75% efficient and the total headloss of the system is 3.5m.
P₁ = 80 kPa B 3 m PB = 50 kPa Calculate the friction head loss for a water Q-1 flowing from point A to B.
Water flows inside a solid cylindrical pipe, which narrows as it goes up to a height h (see diagram below). The lower horizontal section has circular cross-sectional diameter d, whereas the upper horizontal section has diameter d/2. Let us denote A to be a point at the lower horizontal section and B to be a point at the upper horizontal section. The flow speed at A and B is uд and u, respectively. The pressure at A and B is PA and PB, respectively. РА UA Oom Ja d d/21 1 UB h (a) Assuming water to be incompressible, show that the flow speed at B is four times the flow speed at A. (b) Use Bernoulli's equation to find the drop in the water pressure from A to B. Express the result in terms of h, uд, the density of water p, and the acceleration of gravity g. (c) Above certain critical height h, vapour bubbles start to appear at the top horizontal section, which hinders water flow through the pipe. Explain why this happens.
Please assist me with this problem as soon as possible.
Find the cross sectional area of pipe Discharge=77 m3/s Velocity=10 m/s
A pipe carrying water tapers from 300 mm diameter to 150 mm diameter. Section l is 8 m and Section 2 is 3 m above the reference line. The pressure at section 1 is 2 MPa and at section 2 is 0.5 MPa, both are above atmospheric pressure. The discharge is 2.4 m3/min. Find i. The head loss between section 1 and 2 by using Bernoulli's equation ii. Difference of kinetic heads between section 1 and section 2 /// 7//// / ! // Q=2.4 m³/min 8 m 3 m Reference line P-2 Мра =300 mm P-0.5 Мра D=150 mm
A pipe tapers over 60m from 450mm in diameter to 675mm in diameter. The gauge pressure at the inlet is 75 kN/m2 and the gauge pressure at the outlet is 90 kN/m2. If the centreline of the pipe rises at a gradient of 1 in 80 and the energy loss due to friction is 0.01m per metre length determine the flowrate in the pipeline and the velocity at entry and exit.
A pipe of 50 mm diameter and 4,5 km length connects two reservoirs whose constant difference of water level is 12 m. A branch pipe 1,25 km long and taken from a point distance of 1,5 km from reservoir A, which leads to reservoir C whose water level is 15 m below that of reservoir A. Find the diameter of the branch pipe so that the flow into both the reservoirs is the same. Assume the coefficient of friction for each pipe, f=0.0075,and neglect minor losses.
The power 365 W is required to transmit 6 x 10- m/s of water. Find the loss of head due to friction in a pipe. The head loss due to fricțion (in m of water)