1. Using mesh analysis, calculate the current and voltage phasors to describe the voltageacross the inductor and the current in the inductor for the circuit shown in Fig. 1.VL1VuVectorPhaseVectorPhaseLengthAngleLengthAngleCalculatedC3R16202C133nF(R333nF1kQV22.12Vpk5kHzV1[L12.83Vpk5kHz0°15mH60°Figure 1. Circuit diagram.

Answered: Image /qna-images/answer/6333a556-53eb-471e-bf4a-a48586fe0720.jpg

1. Using mesh analysis, calculate the current and voltage phasors to describe the voltage across the inductor and the current in the inductor for the circuit shown in Fig. 1. VL1 VI Vector Phase Vector Phase Length Angle Length Angle Calculated C3 R1 6202 C1 R3 33nF 33nF 1kQ V1 L1 V2 A2.83Vpk 5kHz 2.12Vpk 5kHz 15mH 0° 60° Figure 1. Circuit diagram.

1. Using mesh analysis, calculate the current and voltage phasors to describe the voltage across the inductor and the current in the inductor for the circuit shown in Fig. 1. VL1 VI Vector Phase Vector Phase Length Angle Length Angle Calculated C3 R1 6202 C1 R3 33nF 33nF 1kQ V1 L1 V2 A2.83Vpk 5kHz 2.12Vpk 5kHz 15mH 0° 60° Figure 1. Circuit diagram.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 250-Q resistor and a 4-µF capacitor are connected in series across a sinusoidal a.c. supply for which the angular frequency o is 1250 rad/s. The only other component connected across the supply is a 200-2 resistor. The supply voltage is 64 V r.m.s. 26. Calculate the total current drawn from the supply in A 0.64 В 0.58 C 0.52 D 0.49 amps. 27. Calculate the phase angle between supply voltage and supply current in degrees.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. For the following pairs of voltage and current, indicate their phase relationship (e.g. v leads i by 10°). Analyze whether the element involved in each pair is a resistor, inductor, or capacitor. Also obtain the value of R, L, and C if sufficient data are given.
In the drawn circuit, a student has attached three identical light bulbs to the three wire segments as drawn in the picture. Bulb #1 is in series with a resistor of the same resistance as each lightbulb. Bulb #2 is in series with an inductor. Bulb #3 is in series with a capacitor. Using only qualitative resoning, describe the short term behavior of the lightbulbs. E, + m
3. For the circuit, (i) Find the voltage vc and the current ic if the capacitor was initially uncharged and the switch is thrown into position A. (ii) Find the voltage vc and the current ic if the switch is thrown into position B. (iii) Plot the waveforms for the questions (i) and (ii) for both the voltage vc and the current ic. Mark the time constant for part (i) and part (ii) in the waveforms with the corresponding values for current and voltage. A ww ic 20 kΩ B + + 12 V Vc. R, •10 kΩ 0.05 μF
Problem 4-A 80 kHz sinusoidal voltage has zero phase angle and a maximum amplitude of 25 mV. When this voltage is applied across the terminals of a capacitor, the resulting steady-state current has a maximum amplitude of 628.32 μA. a) What is the frequency of the current in radians per second? b) What is the phase angle of the current? c) What is the impedance of the capacitor? d) What is the capacitance of the capacitor in microfarads?
For the following pairs of voltage and current, indicate their phase relationship. Analyze whether the element involved in each pair is a resistor, inductor, or capacitor. Also obtain the value of R, L, and C if sufficient data are given.
Short Problem: Given a parallel RLC circuit comprised of the following element: 63.92-ohm resistor, ideal inductor with reactance of 46.65 ohms; and a capacitor with reactance of 8.65 ohms. Compute for reactive power in VArs given an ac voltage source of 100 cis 0 volts. Give only the absolute value. Note: Follow this reminder carefully. Compute to the nearest 4 decimal places. No Scientific notation. Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed. Excessive number of decimals as compared to the required number of decimals may result to an incorrect answer.
Consider the sinusoidal voltage and current for an inductor. If you are given the phase angle of the voltage, the phase angle of the current will be:a) The same as the voltage phase angleb) 90°more than the voltage phase anglec) 90° less than the voltage phase angled) Dependent on the inductance
Suppose that an inductor (L) - resistor (R) – capacitor (C) circuit is connected to an AC source that has a frequency of n rad/s. An engineer measured the values: the resistor's resistance which was found to be 10 ohms, the inductor's inductance was found to be 10 H, while the capacitor's capacitance was found to be 10 F. Determine the value of impedance. а. 10 ohms b. 33 ohms с. 11.5 ohms d. 1,080 ohms
Determine the charge on each plate. O For the network of fig a. Find the fotal capacitance. Hw 4 b. "Determine the charge on each plate. C. Find the Voltoge across cach capacitors. d.determine the energy stored by cach capacitor. C3 loouf 20 UF 25HF E O For the network of fig a- Find the total capacitance. 6.Delermine the charge C- Finel the total charge. energy stored on each plate. d. Determine the by each Capacitor. 50 HF 201 CI 30 UF 40MF C3 Q3 C2
Given a parallel RLC circuit comprised of the following element: 72.92-ohm resistor, ideal inductor with reactance of 29.21 ohms; and a capacitor with reactance of 9.43 ohms. Compute for reactive power in VArs given an ac voltage source of 100 cis 0 volts. Give only the absolute value. Compute to the nearest 4 decimal places. No Scientific notation. Do not round off in the middle of calculation. Use stored values.
A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a resistance of 1050 Ohms, an inductance of 0.06 Henrys, and a capacitance of 0.009 coulombs per volt. - omega for source in rad/s? - omegaR for circuit? -XL? -XC? -phi in radians? -Z? -imax?