1. Two forces and a couple are applied to the beam in an attempt to lift it. Replace this force system by an equivalent force-couple system with the force acting at |(a) point A; and (b) point B (c) Determine the resultant force acting at point C and the distance b. 36 kN 20 kN 3m 2m 94 kN m

Q: Impact velocity equation

A:

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

A:

Q: 2. Sharp notches are often added to plastic food packages to help open them (along with arrows…

A: Detailed explanation:Sharp notches are a very good example of the functional features to the plastic…

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: I need answers to problems 4, 5, and 6 pertaining to the print provided.

A: In the given print the length and diameter of the part is to be calculated. Which is mentioned in…

Q: Statics; working

A:

Q: 3

A: intro- defects on any material is cause of failure of material.

Q: The type maintenance requires periodical inspection and testing.

A: Preventive maintenance/periodic maintenance/ planned maintenance is driven by time, meter or event…

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: Files are used for removing large of amount of materials. Select one: True False

A:

Q: The pipe assembly shown is subjected to a force F= 600 N. The pipe has an inner diameter of 20 mm…

A: Consider the Free Body Diagram: Torque,T=600*0.2 =120 N.mTorque acting on part BC,TBC=120 N.mTorque…

Q: Which of the following is NOT TRUE? Choose one: a. Even though a material has a Poisson's ratio of…

A: Introduction: Hooke's law states that "for tiny deformation, stress is exactly proportional to…

Q: discuss the process of creating a good finish when using metals as a raw material in making a…

A: we are to discuss what are methods of generating a better finish with metals

Q: In drawing process, tensile forces are used to reduce the cross section of the workpiece. Select…

A: The drawing process is generally is done at the room temperature. To reduce the required forces, it…

Q: (a) Figure Q2(a) shown the nut slides down the cord OA. When it is at the midpoint, its speed is 200…

A: Givenspeed=200mm/sAcceleration=10mm/s2

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: What are limits or limits of size?

A: This question belongs to Metrology. Metrology is a science of measurement by using different…

Q: a)Prepreg formation results in   Tape consisting of randomly oriented fibers Sheet consisting of…

A: Since you have posted multiple independent Multiple choice questions. We will solve the first…

Q: The thin plate with four holes as shown in Figure 6 has a mass per unit area of 33 kg/m². The radius…

A:

Q: Rolling friction occurs when one surface slides over another surface  Select one: True False

A: Rolling friction is seen between the two surfaces which are in rolling.contact

Q: The possibility to make the required shape from the material is considered during the criteria for…

A: Material to make the desired shape is considered during the criteria of selection. Because during…

Q: Q3/ Consider a point in a structural member that is subjected to plane stress. Normal and shear…

A:

Q: Assume oz = 500, ay = 300, Txy = 250, oyicld = 350. Answer the following questions. Click here for…

A: GIVEN DATA σx= 500MPa σy= 300MPa τxy= 250MPa We have to find maximum and minimum normal stress on a…

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: Q1) Define the following: 1) The stress & the strain 2) Mechanical stress and mechanical strain 3)…

A: Define the Following The stress and the strain Yield strength Tensile Strength Modulus of elasticity…

Q: This statement is true or false? Process of making raw material to a final desired product is called…

A: Given Data : Raw Material Final desired product

Q: In the context of our teaching, which one of the below statements is mostly correct about in…

A: Component design, sometimes known as atomic design (though we prefer "Component design" at…

Q: se explain how you got the P1 and P2 final numbers from the giv

A: We have given in question T=200 and 250 degrees Celsius P=17.3 and 74.4 mm of Hg

Q: Material is forced through a die opening called Drawing Select one: OTrue O False

A: A metals working process in which the material is forced through a die such as metal, glass of the…

Q: 8. For the cross-section of a beam shown; a) locate the centroidal axis from the bottom of the…

A:

Q: Which machine would you recommend given the following information and interest rate is 10%? New Used…

A: Given data as per the question  Interest rate = 10% Calculations considering 1st machineInital cost…

Q: 500N 100N 300mm 800 N 900 N 28°

A:

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: find the length of (20mm) diameter bore is equal to that in the (30 mm) diameter bore,

A:

Q: What is the sliding block?

A: To Define: Sliding block

Q: In wire drawing process, the cross sectional area of wire is reduced. Select one: True False

A: In wire drawing, Material is extruded .

Q: 1- Metals is more - --than ceramic in this property. 2- The engineering design deals with ----and 3-…

A: Dear Student, As per the Bartleby answering guidelines we are supposed to answer first 3 questions.…

Q: What are the concentrated forces?

A: Concentrated forces are more a  mathematical idealizations than a realistic. Force applied at a…

Q: Fine-grained materials have stress-hardening properties. a. True b. False

A: To be explained :-Effect of fine-grained materials on stress hardening properties

Q: Where does a nonconservative force occur, so that mechanical energy is not conser OA

A: Here non conservative force occurs at point "C" that is point of contact of wheel and ground. Non…