1. The triangular block shown in Fig. P-010 is subjected to the loads P = 1600 Ib and F = 600 lb. If AB = 8 in. and BC = 6 in., resolve each load into components normal and tangential toAC.Figure P-010F = 600 lbP = 1600 lb2. In Fig. P-226 assuming counterclockwise moments as positive, compute the moment of force F = 200 kg and force P = 165 kg about points A, B, C, and D.AC0.3 mImathalino,0.3 mFigure P-226 2. A wheel of 10-in radius carries a load of 1000 lb, as shown in Fig. P-324.(a) Determine the horizontal force P applied at the center which is necessary to start the wheel over a 5-in. block. Also find the reaction at the block.(b) If the force P may be inclined at any angle with the horizontal, determine the minimum value of P to start the wheel over the block; the angle P makes with the horizontal; and thereaction at the block.10"1000 lb5"MATHalino.comFigure P-324

Given:- To find:- Force components normal and tangential to AC

1. The triangular block shown in Fig. P-010 is subjected to the loads P = 1600 lb and F = 600 lb. If AB = 8 in. and BC = 6 in., resolve each load into components normal and tangential to AC. Figure P-010 F = 600 lb A B.

1. The triangular block shown in Fig. P-010 is subjected to the loads P = 1600 lb and F = 600 lb. If AB = 8 in. and BC = 6 in., resolve each load into components normal and tangential to AC. Figure P-010 F = 600 lb A B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the frame in (Figure 1). The crate weighs 550 lb. Follow the sign convention. Figure 4 ft O] Al B 1.5 ft 1.5 ft 1.5 ft 1.5 ft . F 6) C . E D 1 of 1 0.4 ft Determine the normal force at point F. Express your answer in pounds to three significant figures. Np = Submit ▼ Part B VE ΑΣΦ Vp = Request Answer Determine the shear force at point F. Express your answer in pounds to three significant figures. vec IVE| ΑΣΦ | | vec 1 当 ? ? lb lb
As shown in the figure, rod AB is steel and rod BC is an aluminum, are hinged to rigid suppots which are pinned together at B to carry a vertical load P=20kN. Each rod has a cross-sectional area of 400mm^2 and Es=200000Mpa and Ea=70000Mpa. Compute for the deformation of steel and aluminum and for the horizontal and vertical displacements of point B.
For the beam with coordinate shown in figure. Develop the flexibility matrix. 1 L 2 C 12 B
An Eccentric force P is applied as shown in the figure below
Bronze Steel Steel W = 40 kips %3D 2 ft 2 ft 2.
A joint is made by gluing two plywood gussets of thickness t = 0.56 in to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 12.65 in and the applied force is P = 7475 lb. Round off the final answer to three decimal places.
Calculate deflection of bd
Column W200 x 71 shown in Figure 1 has the length of 4m has load of P = 150kN acting at e = 50 mm. Given the following data: E = 200 GPa, P = 150 kN and factor of safety = 2, calculate the maximum normal stress in the column. L A ========= 2 Section A-A
A rigid bar XYZ as shown in the figure below is hinged at X and is supported at Y. If the stress in the steel rod is limited to 150 ksi, determine the largest possible load P that can be applied at point Z.
An aluminum bar of cross-section 450 ??² is acted upon by the forces as shown in the figure. Determine the total elongation of the bar. Use ? = 70 ???.
A rectangular steel block is 4 inches long in the x direction, 3 inches longin the y direction, and 4 inches long in the z direction. The block issubjected to a triaxial loading of three uniformly distributed forces asfollows: 48 kips tension in the x direction, 60 kips compression in the ydirection, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 ×106 psi, determine the single uniformly distributed load in the x directionthat would produce the same deformation in the y direction as the originalloading. Note provide a diagram/figure. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.