1. The signal powerleaving a generatoris 3 dBm. It is connectedto an amplifier by a cable 4 ft. long. The attenuation/foot of the cable is 0.2 dB/ft. the gain of the amplifieris 30 dB. What is the output power?2. Given:IL = 1dBPin = 10dBmPix.Pout100cableWhat is the output power in dBm?3. Giventhemultistage cascaded amplifier system below. What is the output powerin dBm?0.3 ft1ft5 ft>A A> APoutPin20 dB15 dB10 dBAttenuation/footPin =- 5dBm=1dB

We need to find out output power for given amplifier

1. The signal power leaving a generator is 3 dBm. It is connectedto an amplifier by a cable 4 ft. long. The attenuation/ foot of the cable is 0.2 dB/ft. the gain of the amplifieris 30 dB. What is the output power? 2. Given: IL = 1 B Pout Pin = 10dBm Pa 100 cable What is the output power in dBm? 3. Giventhemultistage cascaded amplifier system below. What is the output powerin dBm? 1ft >A A> A 0.3 ft 5 ft Pout Pin 20 dB 15 dB 10 dB Pin =- 5dBm Attenuatiaoot =1dB

1. The signal power leaving a generator is 3 dBm. It is connectedto an amplifier by a cable 4 ft. long. The attenuation/ foot of the cable is 0.2 dB/ft. the gain of the amplifieris 30 dB. What is the output power? 2. Given: IL = 1 B Pout Pin = 10dBm Pa 100 cable What is the output power in dBm? 3. Giventhemultistage cascaded amplifier system below. What is the output powerin dBm? 1ft >A A> A 0.3 ft 5 ft Pout Pin 20 dB 15 dB 10 dB Pin =- 5dBm Attenuatiaoot =1dB

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

common
1 For the low-frequency response of the FET amplifier (2N3823) in Figure 1 and the FET data sheet in Table 1, answer the following VDD +10 V Rp 0.001 uF 1k out 0.001 uF 10 kl R, 50 2 RG 10 M0 Vin Figure 1 Table 1 Gate Reverse Current V - Ovdc, V = 30Vdc V = OVdc, V= 30Vdc 2N3821 2N3822 2N3823 0.1 0.1 0.5 nA nA nA uss as V = Ovdc, V= 20Vdc Drain Current Vg = 15Vdc, V = Ovdc 2N3821 2N3822 2N3823 2.5 10.0 20.0 Ioss Gate-Source Cutoff Voltage V = 15Vdc, ID = 0.5nAdc 2N3821 2N3822 2N3823 4.0 6.0 8.0 Vdc Vdc Vdc GS(OFF)
1. Which of these is incorrect for an operational amplifier? a) It has a high voltage gain b) It is a direct coupled amplifier c) It is only useful for amplifying AC signals d) It was originally designed to perform mathematical operations
1. Which of these is incorrect for an operational amplifier? a) It has a high voltage gain b) It is a direct coupled amplifier c) It is only useful for amplifying AC signals d) It was originally designed to perform mathematical operations
2. Derived the formula of output signal to get the equation of Noise?Current gain In the same way, when power gain is calculated using current instead of power, making the substitution , the formula is: 3. In many cases, the input and output impedances are equal, so the above equation can be simplified to: 4. This simplified formula is used to calculate a current gain in decibels and is equivalent to the power gain only if the impedances at input and output are equal. 5. The "current gain" of a bipolar transistor, or , is normally given as a dimensionless number, the ratio of to (or slope of the -versus- graph, for ). An amplifier has an input impedance of 50 ohms and drives a load of 50 ohms. When its input () is 1 volt, its output () is 10 volts. What is its voltage and power gain? 8. Voltage gain is simply? 9. The units V/V are optional but make it clear that this figure is a voltage gain and not a power gain. Using the expression for power, P = V:/R, the power gain is? 10. The…
Noise Figure (F) of an amplifier at room temperature is 0.2 dB. What will be the effective noise temperature (Te). Assume room temperature to be 295K.
1. Which of these is incorrect for an operational amplifier? a) It has a high voltage gain b) It is a direct coupled amplifier c) It is only useful for amplifying AC signals d) It was originally designed to perform mathematical operations
Please answer in typing format please ASAP for the Please I will like it please I appreciate your support and I
QUESTION 1o For the amplifier circuit below given Kp 2.4mA/V essume A0, Vip1.5V. Q point(1.7mA, 3.JV), VDC-10V, R135OK ohm, l2-242K ohm, R 3SKohm, R sig 2kohm Determine the value of gin ms Signal Source
Problem 1 - Design an inverting amplifier with a gain of -24. Please draw the resulting circuit and block diagram.
What is the power gain of the amplifier circuit in the figure? For BJT: beta(F) = hFE = 100 beta(f) = hfe = 200 VBEQ = 0,6V VT = 25mV hre = hoe = 0
eletronic communication system