Answered: 1. The semi-gravity retaining wall…

1. The semi-gravity retaining wall shown in Figure 2.1 Figure 2.1 is made of mass concrete with a unit weight of 23.6 kN/m. Determine it's deadweight per meter length. 730 60 ¥ 60 120 360 ti 300

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter15: Retaining Walls, Braced Cuts, And Sheet Pile Walls

Section: Chapter Questions

Problem 15.5P

See similar textbooks

Similar questions

Figure Question 2 depicts the design of a gravity retaining wall for carthquake condition given: Kv-0 and Kh-0.37 What should be the weight of the wall for a zero-displacement condition? Use a factor of safety of 2.4. What should be the weight of the wall for an allowable displacement of 50.95 mm? Sand $:= 35° %3D Sand $=37 3. Figure Question 2 B Give a comprehensive detail on how to analyze a retaining wall
1. A masonry dam 60cm on top and 3 m at the bottom and 7 m high has water 5 m deep acting on its vertical sides. Specific weight of masonry is 23.54 KN/m^3. How far is the vertical resultant force from the toe? 2. A 0.65-meter diameter window has its center five meters below the water surface. Determine the force acting on the window considering the window is submerged vertically.
7. Water is acting on the vertical side of a trapezoidal masonry dam 2m wide at the top, 15m wide at the bottom and 20m high. If the allowable compressive stress at the toe is 345kPa and neglecting the hydrostatic uplift. Compute the depth of water. Assume the unit weight of concrete=23.50kN/m³ a. 19.76 b. 18.92 c. 17.43 d. 13.54 8. From the previous problem, compute the Factor of safety against overturming. a. 3.142 b. 4.578 с. 3.579 d. 9.766 9. From problem #7, compute the factor of safety against sliding. Use the p=0.60 a. 1.609 b. 2.666 c. 1.365 d. 1.252
A retaining wall is shown in Figure 1. Determine the Rankine active and passive force, per unit length of the wall and the location of the resultant with the following measurements and parameters given:
A 60 cm Cl main pipe leads from a reservoir whose water surface is at Elev. 1590 m. Below the ground surface level, the main pipe is horizontally positioned at Elev. 1410 m. Assuming static condition, what is the stress in the pipewall if the wall thickness is 12.50 mm and the soil pressure is 520 kPa? a. 18.2 MPa O b. 20.5 MPa O . 28.7 MPa O d. 32.6 MPa
If the tubular shaft has an allowable shear stress of 65MPa, determine the required wall thickness of the shaft. The outer diameter of the shaft is150mm.
For a linear stress variation over the base of the dam and neglecting hydrostatic uplift. 70m note: sg concrete=2.5 40m 60m 10 6. Locate where the resultant crosses the base a. 5.59 m b. 6.28 m c. 8.42 m d. 10.51 m 7. Compute the maximum compressive stress at the base a. 1390 kPa b. 1186 kPa с. 463 kPa d. 508 kPa
A masonry dam 4 m on top, 16 m at the bottom and 24 m high has water 21 m deep on its vertical side. Neglecting hydrostatic uplift, (a) what is the vertical component of the resultant reaction force? (b) what is the soil pressure at the toe? (c) what is the soil pressure at the heel?Assume weight of masonry as 2,400 kg/m³.
A retaining wall is shown in the Figure below. For each problem, determine the Rankine active force, Pa, per unit length of the wall and the location of the resultant. H 12 m H₁ 4m Surcharge Frictionless wall Sand 71 di =0 Y₁ Y₂ 17 kN/m² 23.2 kN/m² ↓ Groundwater table i(deg) : (deg) 36 42 4 25 kN/m² Sand Ey (saturated unit weight) DE MOITAMINE 72 -0
A water tank, 15 m in diameter and 10 m high, isproposed for a site where there is an existing pipeline(Figure P7.26). Plot the distribution of vertical and lateral stress increases imposed by the water tank on the pipeline along one-half the circumference nearest to the tank.The empty tank’s weight (deal load) is 350 kN. Assume thewater tank is fi lled to its capacity
I need an answer to the factor of safety again overturning.
I need the answer as soon as possible