1. The right-hand motor rule is usually used to determine a. flux density. b. the direction of conductor movement. c. conductor speed. d. flux direction. e. induced current. 2. In Figure 14-9, conductor movement will be a. upward. b. downward. c. to the right. d. to the left. e. constant. Figure 14-9 Conductor movement. N S 3. Torque on a single loop of wire in a magnetic field is a. constant. b. strength. c. the same as field flux. d. the turning force. e. never at a maximum value.

1. The right-hand motor rule is usually used to determine a. flux density. b. the direction of conductor movement. c. conductor speed. d. flux direction. e. induced current. 2. In Figure 14-9, conductor movement will be a. upward. b. downward. c. to the right. d. to the left. e. constant. Figure 14-9 Conductor movement. N S 3. Torque on a single loop of wire in a magnetic field is a. constant. b. strength. c. the same as field flux. d. the turning force. e. never at a maximum value.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

define energy and co-energy and sho them in graph of bonding flux with respect to Magnetizing current
SOLVE AND SHOW YOUR COMPLETE SOLUTION. ANSWERS SHOULD BE IN TWO DECIMAL PLACES. The armature of a two-pole dc machine has 30 slots, each slot has 4 conductors each. during its operation, only 75% of the conductors are directly under the pole. each pole measures 2 inches by 3 inches and produces ten million maxwells of flux. the armature core is 12 inches in length and 3.5 inches in diameter. the total resistance of the winding is 2 ohms. e) Determine the total torque exerted by the armature core in ft - lb if the winding is simplex lap winding.
The symbol for flux density is and the unit is Magnetic lines seek A conductor is carrying current away from you. Mark on a diagram the direction of the magnetic field Conductor carrying current produce. B is the symbol for and the unit is or or
Question 6 Copper losses represent: O A. Losses due to friction of the moving parts O B. Windage losses O C. None of the other choices are correct O D. Friction losses in the windings of the machine E. Losses due to magnetization and demagnetization of the core
SOLVE AND SHOW YOUR COMPLETE SOLUTION. ANSWERS SHOULD BE IN TWO DECIMAL PLACES. The armature of a two-pole dc machine has 30 slots, each slot has 4 conductors each. during its operation, only 75% of the conductors are directly under the pole. each pole measures 2 inches by 3 inches and produces ten million maxwells of flux. the armature core is 12 inches in length and 3.5 inches in diameter. the total resistance of the winding is 2 ohms. b) determine the total generated voltage if the armature is running at 1000 rpm and its winding is simplex lap connected.
How are eddy current losses affected by the frequency and density of the flux wave?
Please answer in typing format
A. The brushes used in a DC generator a) ride against the commutator segments. b) are made from material softer than the commutator segments. c) are generally marked Al and A2 d) all of the above B. A magneto is a DC generator that uses for its pole pieces. a) electromagnets b) permanent magnets c) either "a" or "b" d) neither "a" nor "b"
The capacitor in the rectifier is chosen such that O a. Time constant CR is ten times of that AC output Supply O b. Time constant CR is ten times of that AC input Supply
Which factor does not affect the resistance of the armature winding? A. cross sectional area of the conductor B length of the conductor C. number of the conductors D. strength of the magnetic field
Explain the principles of starting a slotted pole by drawing a phase diagram of fluxes
A wave wound DC generator has 6 poles and the armature has 756 conductors. How fast should the armature rotate if the flux is 20 mWb per pole and 240 V is desired?