R1. The horizontal 4 m long lever, with pivot at A, isacted upon by a parallel force system, as shown.Determine the magnitude and location of theresultant force.1,75 N205|N190 N 65 N250 NBA130 cm120 cm 50 cm 100 cmd.R = R, + R,2. The trapezoidal force distribution shown in thefigure acts on beam AB. Determine the magnitudeand position of the resultant force. L= 4m, W=75N/m and W2= 325 N/m at end B.or250 N/m75 N/md(4 – d)4.00:m3. A three force parallel system acts on beam AB,two of which have known magnitudes and locations(see the figure). If the resultant R is shown, determinethe magnitude and location of the missing third forceof the parallel force system.d.R = 150 N200 N300 NAB60 cm i360 cm330 cm

Answered: Image /qna-images/answer/1da713a9-421b-4252-a40f-7fdbf52fc28b.jpg

Answered: 1. The horizontal 4 m long lever, with…

1. The horizontal 4 m long lever, with pivot at A, is acted upon by a parallel force system, as shown. Determine the magnitude and location of the resultant force.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the Reactions of the beam. Show the Distributed Load Resultant magnitude and location on the loading diagram.
!. Determine the reactions at the supports A and C of the compound beam. Assume A is fixed, B is a pin, and C is a roller. Include the free-body diagram
Note: draw its fbd and solve
REFER TO FIGURE 03, DETERMINE THE MAGNITUDE AND LOCATION OF THE RESULTANT LOAD FROM THE LEFTMOST SUPPORT, AND COMPUTE THE REACTIONS AT THE SUPPORTS.
The solid shaft that is fixed connected at both ends has a diameter of 20 mm and a total length of 2m. If it is subjected to two torques 500 N.m clockwise, positioned 0.3 m from the support A and 800 N.m counterclockwise positioned 0.2 m from the support D. Determine the reactions at fixed supports A and D. Express your final answers in N.m.
3. The shear stress is limited to 60 MPa. Consider G = 84,000 MPa. a. Determine the diameter of a solid steel shaft which will transmit 90kW at 106 revolutions per minute.. b. Determine the length of the shaft if the twist must not exceed one-degree over the entire length. (
The hoist supports the 150-kg engine. Determine the force in members DB and FB. Also determine the reactions on the floor at A and C. m m 2 m BO E 2 m 1m
B 4m 2m Hinge Water 50cm 420cm 30cm A closed cylindrical drum is 30cm in diameter and 50cm high as shown, contains a liquid (SG liquid = 0.83) and a depth of 20cm. The drum is then submerged in water and attached to a beam using a tension wire. Neglect the outer and inner thickness of the drum. To keep the beam in horizontal position, determine the following: a) The force "B" If the specific grawlty of the drum is 1.65; force "B" is Blank 1 KN b) The specific gravity of the d'um if the force B is 160 kg: SG of drun is Blank 2 Blank 1 Add your answer Blank 2 Add your answer
IHE BARS AB AND AC ARE JÕINED BY A PIN AT A AND A HORIZONTAL CABLE. THE VERTICAL CABLE CARRYING THE 200-kg MASS IS ATTACHED TO THE PIN AT A. DETERMINE THE TENSION IN THE HORIZONTAL CABLE. NEGLECT THE WEIGHTS OF THE BARS. 30° 60° 3 m 2 m B 200 kg
A solid shaft made of steel [G = 80 GPa] is subjected to the torques shown. Determine theangle of twist along the shaft measured at gears B, C, D, and E relative to the flange A. Diameter of the shaft is d= 20mm. [TB = 25 N.m; TC = 35 N.m; TD = 24 N.m; TE = 14 N.m][dABCDE = 20 mm (diameter); LAB = 300 mm; LBC = 400 mm; LCD = 400 mm; LDE = 250 mm]
The bars AB and AC are joined by a pin at A and a horizontal cable. The vertical cable carrying the 200-kg mass is attached to the pin at A. Determine the tension in the horizontal cable. Neglect the weights of the bars 200 kg Answer: 1416 N
Show complete solution