1. The circuit below consists of a source connected to a load where the impedance of the load Z, is fixed. vi(1) R www Load L Source Suppose the amplitude of the source voltage is doubled so that v, (t) = 48 cos(3t+75°) V. By what factor is each of the following changed? ↓ a) The load current I. ↓ b) The complex power delivered to the load.

1. The circuit below consists of a source connected to a load where the impedance of the load Z, is fixed. vi(1) R www Load L Source Suppose the amplitude of the source voltage is doubled so that v, (t) = 48 cos(3t+75°) V. By what factor is each of the following changed? ↓ a) The load current I. ↓ b) The complex power delivered to the load.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1: Consider the circuit shown in the following figure. (i) Find the phasor currents and voltages. (ii) Find the power delivered to the load. (iii) Reflect Vs and R1 to the secondary side. V₁= 1000/0° (~ V peak R₁ = 1000 £2 www 10:1 elle m 10 +j20 ZL
COURSE: Electrical EngineeringSUBJECT: Electrical ApparatusINSTRUCTIONS:• Write the GIVEN with their respective symbols and units.• Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units• Round up to 3 three decimal places the FINAL ANSWERS and BOX it. PROBLEM: A source delivers 50 kVA to a load with a power factor of 65 percent lagging. Find the load’s average and reactive powers.
Consider a single-phase load with an applied voltage v(t)=150cos(wt+10°)V and load current i(t)=5cos(wt-50°)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
The power distribution system shown in Figure 1 operates at 50 Hz, 260 V and consists of three loads.consists of. Find the total real and reactive power, the magnitude of the apparent power and the power factor? PowerFind the necessary correction to make the factor 0.935? Which one would you need to do this fix?Determine what reagent component should be obtained?
2. A voltage applied to a load is V=208 4 20°V and current through load is I=10 a–10° A. Find the following [SO 1] o complex power consumed by load o Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power?
IL 220230° Load P = 2 kW pf = 0.9 lag Assuming that the source is operating at 60 Hz, determine the following: a.) The value of the current I, in phasor form the magnitude, degrees for the angle) b.) What is the reactive power Q of the load in (volts for KVAR? c.) Is the load consuming or supplying Q? d.) What is the apparent power S of the load in KVA? e.) What is the load resistance? Express your answer in Ohms. f.) What is the load inductance? Express your answer in millihenries.
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1
Assume that the voltage applied to a load is V = 2082-30° V and the current flow- ing through the load is I = 5Z15° A. (a) Calculate the complex power S consumed by this load. (b) Is this load inductive or capacitive?
Suppose an AC generator with V(t) = (150V)sin(100t) is connected to a series LCR circuit with R = 40 Ohm, L= 80 mH, and C = 500 microFarad, as shown in the figure. Calculate the maximum voltage across the resistor (VR0)? A. 11.52 V B. 6.12 V C. 6.31 V D. 4.12 V
Using Figure 1, Vs 50V-15 339 Hz R1 $1100 R2 100 www XL1 320 HH XC1 Figure 1 700 R3 600 13 R4 400 XL2 1902 XL3 450 XC2 650 a. Determine the total circuit impedance, ZT. b. Calculate current IT. c. Calculate currents I, and I3. State the value of these currents in both rectangular and polar form. d. For each of the currents determined in part c, answer the following: Is the current leading, lagging, or in phase with the source voltage. e. Use the voltage-divider rule to determine the voltages across XL1 and Xc2.
Two single-phase ideal voltage sources are connected by a line of impedance of 0.7 + j2.4 Q as shown in below figure 0.7+ j2.4 N I12 500/16.26° V 58520° V a. source 2 generates active power and receives reactive power b. source 1 receives active power and generates reactive power C. source 1 generates active power and receives reactive power
Three loads are connected in parallel across the 500Z0º volt (rms) source shown below. (a) Calculate the power factor seen by the source assuming that the capacitive reactance Z, is not connected to the circuit. (b) Find the total complex power supplied by the source if a capacitive reactance Z. =-j5N is connected in parallel with the three loads. 50020° Load 1 Load 2 Load 3 Volt (Rms) 60 kW, Pf-0.6 (Lag) 20 kW, Pf-0.8 (Lead) 20 kW, Pf-1 Zc