1. The characteristics of a BJT are shown below. What is ß for the transistor? Consider thecircuit below containing this BJT. Draw the load lines for Vin=0.5V, 0.7V, and 1.0V anddetermine is and Vce for each Vin.iB (μA)100806040200-1000.2T= 300 KVin0.40.6(a) Input characteristic0.8ww2 ΚΩCb==10 ΚΩe1.0+UBE (V)12Vic (mA)6543210Copyright © 2011, Pearson Education, Inc.02ig = 50 μA40 με30 μ.Α20 με10 μ.Α0684(b) Output characteristics1012VCE (V)

Answered: Image /qna-images/answer/62c94b03-5c68-417b-bab5-5de3ea8cccec.jpg

1. The characteristics of a BJT are shown below. What is ß for the transistor? Consider the circuit below containing this BJT. Draw the load lines for Vin=0.5V, 0.7V, and 1.0V and determine iÂ and Vce for each Vin. iB (μA) 100 80 60 40 20 0 -10 0 0.2 Vin 0.4 0.6 (a) Input characteristic 10 ΚΩ b T= 300 K e 0.8 ww 2 ΚΩ 1.0 + UBE (V) 12V ic (mA) 6 5 4 3 2 1 0 0 Copyright © 2011, Pearson Education, Inc. 2 iB = 50 μA 40 με 30 μ.Α 20 με 10 μ.Α 0 8 4 6 (b) Output characteristics 10 12 VCE (V)

1. The characteristics of a BJT are shown below. What is ß for the transistor? Consider the circuit below containing this BJT. Draw the load lines for Vin=0.5V, 0.7V, and 1.0V and determine iÂ and Vce for each Vin. iB (μA) 100 80 60 40 20 0 -10 0 0.2 Vin 0.4 0.6 (a) Input characteristic 10 ΚΩ b T= 300 K e 0.8 ww 2 ΚΩ 1.0 + UBE (V) 12V ic (mA) 6 5 4 3 2 1 0 0 Copyright © 2011, Pearson Education, Inc. 2 iB = 50 μA 40 με 30 μ.Α 20 με 10 μ.Α 0 8 4 6 (b) Output characteristics 10 12 VCE (V)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the DC Voltage for the filtered bridge rectifier with a load as indicated in Figure * 10:1 D1 D3 Output 115 V rms Pipri) 60 Hz p(sec) C. D2 D 50 µF 2.2 kN 11.4 13.4 V 12.4 V None of the above lll
4. Perform the following steps for the given circuits a) Considering the output characteristic of the BJT, find the value of RC required to obtain 12V VCCE junction voltage. RB = 75kQ, RE = 3.3kQ, VCC = 22V. VcC 4!c (mA). 450 μΑ RB IB IC RC 5.0F dol 4.5 400 μΑ 4.0 350 HA Vout 3.5 300 µA e 3.0 VCE 250 μΑ 2.5 VBE 200 µA 2.0 150 μΑ le5 100 HA RE 1.0 IE I = 50 HA 0.5 5 10 15 20 25 Vce (volt)
solve 11
For the emitter-stabilized bias circuit, determine Rg 12 V 2 mA 07.6 V 024 V 270 kohm B) 320 kohm 343 kohm D) 355 kohm
A base bias method is used in the following circuit. For Bpc - 300, the value of emitter current is: -Vc. +15 V Rc 1.8 k2 RB 560 k2 7.82 mA O 6.84 mA O 7.27 mA
1
Answer the question:
5. Determine the collector bias current. Assumeß = 50 and IS = 10^(-17)A Vcc= 2.5 V 100 Κ Ω Σ RB Rc1k Y Ic B O 17mA O 8.5mA O 1.7mA O None of the mentioned. O 0.85mA X
Save An Vcc The following biasing network is called IB RB Vie t Rc Co RE Fixed bias configuration Voltage divider biasing Emitter stabilized blas clrcuit Windo Collector feedback biasing ge ENG ) へ
92 ۱ ۹:۱ ص Qs= 1107 and Qp= 1041 Qs= 1207 and Qp= 1241 Qs= 1007 and Qp= 1041 Qs= 1107 and Qp= 1141 In the figure shown below we can find output current is equal to.. . if the input voltage is equal to 12 mv 12 kO 12 ka 6 ka No option is correct 10 = 32 uA 10 = 34 uA 10 = 38 uA 10 = 36 uA In the fig. shown below we can find the higher critical frequency due to the input
A silicon transistor is biased with base resistor method. If B=100, VBE =0.7 V, zero signal collector current IC = 1 mA and VCC = 6V, what is the value of the base resistor RB? Select one: O a. None of the above O b. 315 ΚΩ Ο c. 530 ΚΩ O d. 105 k
The term "Bipolar" in Bipolar Junction Transistor (BJT) refers to O Two diodes O Two resiIstances O Two junctions O Two polarity carriers (electrons & holes) If the value of dc alpha is 0.5, then the value of dc beta of a transistor is 0.1 O 10 O 100