1. The 10-1b block has an initial velocity of 10 ft/'s on the smooth plane. If a force F = (2.5t) lb, where t is in seconds, acts on the block for 3 s, determine the final velocity of the block and the distance the block travels during this time. v= 10 fus F= (2.51) lb

Q: Question 6 A straight bar is fixed at edges A and B. Its elastic modulus is E and cross section is…

A: A straight bar fixed at edges A & B as shown- Elastic modulus = E, Cross-section area=A, Load…

Q: QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is…

A: Given data :

Q: The beam is analyzed using Slope Deflection Method 1.What is the EI teta C? 2.What is the reaction…

A: Solution

Q: For the beam shown below, AC and BD have the same flexural rigidity equals to 4,000,000 lb.in².…

A: L=25in L'=40in w=100lb/in To find reaction at C and deflection at point C

Q: 1. A 250mm x 300mm beam has a simple span of 12 meters. It is necessary to place a support at…

A: Deflection: The displacement of any structural element in the structure which is displaced under the…

Q: Determine the maximum torque T in kN.m without exceeding a shear of 70 MPa in steel and 50 MPa for…

A: 1. 10.44kn-m

Q: Figure shows a statically determinate beam under distributed loading conditions where C is the…

A:

Q: for the beam shown in the figure, a) find the equation of elastic curve by integration method. b-)…

A:

Q: Find the maximum force P (in N) that can be applied to block A without causing both blocks to move.…

A: Find the maximum force P (in N) that can be applied to block A without causing both blocks to move.

Q: 3. Two beams are supported as shown in the diagram below, each 150mm x 200mm x 4 meters. Beam CD is…

A:

Q: (a) Determine the reactions at A and E if P = 800 N. The reactions are positive if to the right or…

A:

Q: AL SUrtace With an unkhown thictional coefficient egligible frictional coefficient. The panel has…

A:

Q: Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: Coplanar forces: In the coplanar force system, all the forces acting in one plane of action. They…

Q: Determine the minimum force P required to push the crate up the plane. The crate has a mass of 28 kg…

A: The crate is assumed to be stable, then the force applied to move it upward can be calculated by…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A:

Q: Determine the reactions for the loaded beam as shown below. Neglect the weight of the beam. 1201b…

A:

Q: Q2/ Determine the resultant moment of the force about point D F=400N 100 N D 30 A B 45° 0.3 m 100 N…

A:

Q: Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force (P) is…

A: Given Specific gravity of oil=0.82 To find P

Q: a. The reactions at the support for a simple beam loaded as shown. Neglect the weight of the beam.…

A:

Q: The cylinder is subjected to a load that has a weight W. If the coefficients of rolling resistance…

A: The free body diagram of top surface is shown below.

Q: Charges q1, q2 and q3 are arranged in the x-axis. Charge q3 = 14 nC and is at the origin. Charge q2…

A: Given: The charge q2 is 4.5 nC. The charge q3 is 14 nC. The distance between charge q3 and charge q2…

Q: A 335-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A: A pulling mechanism is given and it has been asked to determine load P required. Please refer step 2…

Q: The truss shown is supported by a hinge at A and a roller at B. A load of 2500 lb is applied at C.…

A:

Q: H. A machine operator produces the tension T in the control rod by applying the force P to the foot…

A:

Q: P.L B. 6L-

A: a) Free Body Diagram of the given problem:

Q: The 13 kips force F acting on the simply supported beam. Determine: y component of F

A: The 13 kips force F acting on the simply supported beam. Determine: y component of F

Q: A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze[E =…

A: To determine the stress in the bronze rods (1) and the steel rod (2).   Given, Modulus of…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A: Determine the normal stresses in bronze rods (1) and steel rod (2)

Q: Find a. Reaction at D in mm b. Location Maximum Deflection from D in m c. Maximum Deflection of the…

A: Given a propped cantilever beam with different loading conditions. Cross-section area=150*150 E=20…

Q: slope deflection method and solve for the reaction at support A,B,C

A:

Q: Beam AB has a negligible mass and thickness, and supports the 200-kg uniform block as shown in…

A:

Q: QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is…

A: Solution:-The diagram is shown below, Given data,Torque(T)=200kN.mE=720GPaG=27GPaThe diameter of…

Q: The value of M in the beam ABC shown in the figure is such that the joint B does not rotate. 30 kN/m…

A: Find the Value of reaction at B for the given beam ABC.

Q: A determinate frame carries a concentrated and distributed load as shown in the figure. Determine…

A: Step 1

Q: A building (or machine) is shaken by a periodic force f(t) defined bye -C, --st<- f(t) = 3C, st< 20…

A: According to the guidelines , we are only allowed to answer one question at a time. so I am…

Q: DETERMINE THE FORCE "P" ACTING ON THE BLOCK. THE BLOCK WEIGHS 8000N AND THE SYSTEM IS IN…

A: Given data in question  Weight of block Angles To find out  Force P

Q: Determine the force "P" acting on the block. The block weighs 7000 N and the system is in…

A: →GIVEN DATA:-⇒Weight of Block = W= m×g= 7000 N⇒System is in equilibrium i.e,⇒∑Fx= 0⇒∑Fy=0⇒∑M=0

Q: The 800-lb cylinder is supported by three chains as shown. Determine the force in each chain for…

A: Consider the following free body diagram:

Q: D (5000 mm2) (4000 mm) E (5000 mm) 3 m 4000 mm) (S000 mm?) B (5000 mm?) A 100 kN 2 panels at 4 m 8 m…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.