1. Solve the problem belowGiven:Gage reading at A=82.3kPa absoluteAtmospheric pressure=99.6kPaDetermine:a.) Elevation at Qb) Deflection of Hg (h1) in the U-tube as columnof oil (s=0.7) absoluteEl. 65.00-AirEl. 49.00 m Hsp gr 0.700El. 38.00 mNMWaterEl. 26.00Ra 1.60注2000Еl. 14.00 m

Solution: Given Data: A=82.3 KPaAtmospheric pressure=99.6 KPas=0.7

Answered: 1. Solve the problem below Given: Gage…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 10.7 The shaded area shown in (Eigure 1) is bounded by a, y axes and the curvey²-2.89-0.5 m², where a is in m. Suppose that a = 5.78 m and h = 1.7 m Figure 1 of 1 Part A Determine the moment of inertia for the shaded area about the axis Express your answer to three significant figures and include the appropriate units. 1,= Submit HÅ xa Xs Value Provide Feedback 9 . x.10% X Units Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining ?
Situation #1 3 m El is Constant (Assume El = 1 kN-m²) Y KN 7 10 + A X KN 4 m B 7. Determine the slope at A 8. Determine the slope at B 9. Determine the location of the maximum deflection from A Y= 32 X= 868 A= 5 All units must be in kN or m in the summary. Be consistent with your units. ARGOLLITE
USE GEOMETRIC METHOD FOR SOLUTION
شكسكيه
8: Calculate frictional drag. Placed longitudinally in a stream of oil having the tree stream veloity of 6 m/sec. Also find the thickness of Boundary layer and the shear stress, at on a plate 0.15m wide & 0.45m long the the trailing edge. "Specific gravity of oil is 0.97 & 19 = 0.9×154 mil see.
Asaap
H.W A uniform glass rod having a length L is placed in the smooth hemispherical bowl having a radius r. Determine the angle of inclination 0 for equilibrium. B. 2rCosa Ng Ans: L+VL+128 = Cos 16r Note: By observation o = 8. %3D O REDMI NOTE 9 PRO O AI QUAD CAMERA ル。
Problem#13: Consider a heavy mass of weight W on the following beam system: El = 10° k-in? massiess beam Hipe - 60 in- Assume the damping ratio of the beam is = 10%. If displacement, u, corresponds to the displacement of beam at the location of the attached weight, and if the system is given an initial displacement of 0.5 in and an initial velocity of 15 in/sec determine the following: a. Write the equation of motion of the system – what type of system is it (i.e., under-damped, critically damped, over-damped)? b. The un-damped natural frequency (0.) and period (T.) of the system c. The damped natural frequency (0) and period (T.) of the system d. The critical damping coefficient, c, e. Phase angle of the vibrating motion, 0 f. The peak displacement at time t = Ta + 0/ ma g. The peak displacement at time t= 2T + 0/ o4 h. The log-decrement, 5
Ex-6. A steel tape with a cross-sectional area of 0.039 cm²and weighing 0.909 kg has a length of 30.009 m. when supported throughout 20°C and subject to a tension of 5.5 kg. This tape is used to measure a distance along a uniform 4% grade and is supported throughout during the measurement. The tension applied is 12 kg. The temperature of the tape distance is recorded 381.615 m. What is the corrected horizontal distance? 2°C. The measured slope in Alwa
Prob 2. (15pts) A line was found to be (2865.35+y)m long when measured with a 30-m tape under a steady pull of (6.5+y) kg at a mean temperature of 300C. Determine the correct length of the line if the tape used is of standard length at 200c under a pull of 5.5kg. Assume the cross-sectional area of tape to be 0.025cm2, elastic modulus as 2.10 x 106 kg/cm2, and coefficient of thermal expansion to be 0.0000116/ec.
For the beam loaded as shown in the figure 1, Determine the deflection at B in mm using Double Integration Method. Considering 150 mm x 150 mm section and E = 200GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 5.1 m, b= 19kN/m, c = 18kN please help needed it I already provided all that is needed thank you
Determine the difference in pressure between points A and B. The elevation z, and z2 are 10 m and 11 m, respectively, 1₁-Tm and the manometer deflection 12 is 50 cm. Q3.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

1. Solve the problem below Given: Gage reading at A=82.3kPa absolute Atmospheric pressure=99.6kPa Determine: a.) Elevation at Q b) Deflection of Hg (h1) in the U-tube as column of oil (s=0.7) absolute