1. Sketch the frequency response of the amplifier on a semi-log paper. 2. From the frequency-response plot, determine the -3 dB cut-off frequencies fi and fi of the amplifier, and find the bandwidth. 3. Calculate the lower break frequencies fi, fi2, and fis due to the coupling and bypass capacitors. Find the dominant corner frequency and compare it with the measured value of fi. 4. From your plot, determine the unity-gain frequency fr. 5. Calculate the theoretical value of the mid-band gain, and compare it with the practically measured value.

1. Sketch the frequency response of the amplifier on a semi-log paper. 2. From the frequency-response plot, determine the -3 dB cut-off frequencies fi and fi of the amplifier, and find the bandwidth. 3. Calculate the lower break frequencies fi, fi2, and fis due to the coupling and bypass capacitors. Find the dominant corner frequency and compare it with the measured value of fi. 4. From your plot, determine the unity-gain frequency fr. 5. Calculate the theoretical value of the mid-band gain, and compare it with the practically measured value.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the integrating amplifier circuit in Figure 2. Using nodal analysis, derive an expression for vout for the integrating amplifier. In the circuit in Figure 2, exchange the positions of the 0.1uF capacitor and the 5k resistor. a. Use nodal analysis to generate an expression for vout. b. Using this expression, explain what function this circuit performs on an input signal.
4. What is meant by Bandwidth of an amplifier?
Question 7) Design a JFET amplifier network with ldss-8 mA, Ve=-4 V, R1=110 MN, R2=10 MQ. When an input AC signal V=10 mV is applied to the network, an output signal Vo=2V AC is obtained. (suppose that ra2 10R0) a) Draw the JFET amplifier network you prefer to design, and explain why you choose this network b) Explain the aims and reasons in using of all the peripheral components handled on your network c) Draw AC equivalent re model of the network (5p.) d) Draw transfer characteristic curve and derive lda and Vasa values from the characteristic curve e) Calculate Av, gm, VoD, Ro, Rs, Z; and Zn. Note: Please, do not forget using resistors and capacitors as peripheral elements whatever required for your complete design in the question (i.e. input, output terminals etc.)
Q.3 Figure Q.3 shows an AC equivalent circuit at high frequency for a common-emitter BJT amplifier circuit. The voltage gain, Ay is -40. 1502 4 pF + Em V, RL Vo 3pF 2kΩ 100pF IpF 4pF Figure Q.3: AC equivalent circuit at high frequency operation (а) Determine the high cut-off frequency due to the input side of the equivalent circuit, fHi- (b) Consider that the high cut-off frequency due to the output side of the equivalent circuit, fHo, is 80 MHz. State the dominant high cut-off frequency.
1- Draw the frequency response of the amplifier on a semi-log paper. 2- From the frequency response plot, determine the -3 dB cut-off frequencies f₁ and f of the amplifier, and find the bandwidth. 3- Calculate the lower break frequencies fLc, fls, and fle due to the coupling and bypass capacitors. Find the dominant corner frequency and compare it with the measured value of fL. 4- From your plot, determine the unity-gain frequency fr. 5- Calculate the theoretical value of the mid-band gain, and compare it with the practically measured value. 6- What is meant by one decade, and one octave?
An RF amplifier is composed of a cascade of two amplifier devices. The first has a power gain of 190W/W. The second has a power gain of 100W/W. What is the overall power gain of the cascade in dB (to two decimal places)?
Subject : Electronics Engineering A CE amplifier has mid frequency gain of 200. The upper and lower 3dB frequency of the amplifier is 10KHz and 100KHz respectively. A negative feedback of 10% is incorporated in the amplifier circuit. Find the new gain and new bandwidth after feedback?
Q.3) In frequency domain enhancement, we have many types of low pass filter, mention them and explain the using of each one.
on to Electronic Analysis and Design- CE255/EE255 - C courses / Introduction to Electronic Analysis and Design - CE255/EE255 - O1 - Spr The Common Emitter BJT Amplifier has Select one: a. Has a negative gain. b. The input impedance is always very low, whatever the design is. c. The output impedance is always very high, whatever the design is. d. Has a positive gain. e. The gain is always less than 1, whatever the design is. age ssessment CE255/EE255 (O1) - Dr. Mamoun Al-Mistar Jump to...
2.A. Using an operational amplifier draw the circuit diagram of a noninverting amplifier with a voltage gain of 25. Show all power supply connections, input and output voltages, and give appropriate values for the resistors. - B. If the voltage gain is increased to 200, what effect will this change have on the bandwidth of the amplifier and why is this so? {C. If the resistance of the transducer connected to the input of the noninverting amplifier is increased from 50 ohms to 50k ohms, what effect will it have on the voltage gain of the amplifier. D. What effect will the change in transducer resistance from 50 ohms to 50k ohms have on the output and why is this so?
a) What is the input impedance of an inverting amplifier circuit? What is the input impedance of a non-inverting amplifier circuit? b) What is the formula for the gain of an inverting operational amplifier circuit with input resistor Ri and feedback resistor Rf? Draw the circuit. c) What is the formula for the gain of a non-inverting operational amplifier circuit with input resistor Ri and feedback resistor Rf? Draw the circuit.
FIND THE CURRENT, VOLTAGE AND POWER FOR R1,R2,R3,AND R4.