Question 1 pls. Complete soln. Thanks 1. Show the steps in the derivation of the cantinuity equation.2. Show the steps in the derivation of the Bernoulli's equation3. Enumerate and describe the similitudes applied for prototyping and modellingtechniques.

Answered: Image /qna-images/answer/622d6ec5-00f4-46bd-9eb9-b83128cc5ed2.jpg

Answered: 1. Show the steps in the derivation of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3) The unit of force in S.I. system of units is dyne O kilogram O Newton watt
1.10 Figure 1.24 shows a special spanner used to tighten screwed components. A torque is applied at the tommy- bar and is transmitted to the pins which engage into holes located into the end of a screwed component. (a) Using the data given in Fig. 1.24 calculate: (i) the diameter D of the shank if the shear stress is not to exceed 50 N/mm², (ii) the stress due to bending in the tommy-bar, (iii) the shear stress in the pins. (b) Why is the tommy-bar a preferred method of applying the torque? 26 26 5 [C.G.] [9.14 mm; 254.6 MN/m²; 39.8 MN/m².] Mechanics of Materials 50N force applied at a distance of 25 mm from both ends of tommy bar Q Fig. 1.24. 05 100
The volume of a 45’ container is 87.16 m3. The internal measures are: Length: 44’4” ft Height: 8’4” ft What is the width of the container?
Draw A.F.d & S.F.d & B.M.d
03C) A 20 KN force makes an angle of 30° with the vertical. This force is acting at a horizontal distance of 2 m from the center. The moment of this force will be O a. 15 KN.m O b. zero O c. 20 KN.m O d. 35 KN.m ENG 08:3 US 06/07/ hp 12 144 & 8.
7/. In stress strain curve the maximum stress the material withstand without breaking is represents by the letter _________ a. E b. A c. F d. B
3 kN/m. EN 8. A Draw Zm. TS.F. 9 B.M.)
Q3/ including setting the machine, a worker manufactures 79 pieces of different tools in 7 hours and 15 minutes. If the standard time for the tool was Setting time = 40 min Production time per tool= 10 min Compute: 1-The standard time for manufacturing the 79 tools 2-Efficiency of operator
h) Strain energy for truss CE. Enter your answer in J to 2 decimal places.
• Part A Draw the shear diagram for the baam. Folow the sign convention. Fig.m 1) Clok on "add Vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add funotions between the lines. Note 1- You chould not draw an "extra" vertical line at the looation of appled moment. Note 2- Be cure to Indicate the oorreot types of the funotione between the linec, eg. fin your ancwer the type of a funotion Ie "Ilnsar inoressing ciope" for the funotion that actually has linear deoreacing clopa, the ancwer wll be graded as Incorrect Uce the button "ohange cagment" f nsoeccary. 0000 15 kN 10 kN/m 20 kN m 2m 1m No cloments selected v N) 30 20 Im) 20 Add discontinulty ines and seloct segments to add to the canvas Submit dg Aer • Part B Draw the momant diagram for the baam. Follow the sign convention. Cliok on "add vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add funotions between the lines. Note 1- The ourve you chooce from the drop-down…
convert (3.75 mm.kg)/(3ft).
1-5) The costs, C, to manufacture a part using either method A or method B are estimated by the following formulas CA = 32 + 0.85P CB = 74 + 0.9P – 0.010P², where the cost C is in dollars and P is the number of parts. (a) Estimate the breakeven point, ie the number of parts where the cost from either method is the same. (b) Which method would be less expensive to produce 100 parts?

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

1. Show the steps in the derivation of the continuity equation.