For the cable shown in, determine the following1. reactions for the cable2. the sag y at the 45-kip load.3. Cable length10 ftB30 ft145 kips65 kips85 kips30 ft50 ft-50 ft-- 30 ft -4.

Answered: Image /qna-images/answer/d477002f-304b-4b17-977d-1784a2d8f032.jpg

Answered: 1. reactions for the cable 2. the sag y…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

-3m A BEFORE THE FRAME IS LIFTED BY THE CABLE AD, ITS POSITION IS AS SHOWN IN THE FIGURE. AT WHAT ANGLE WITH THE HORIZONTAL WILL THE FRAME TILT AND WHAT WILL BE THE 4m TENSION IN CABLE AB? W-12kN
Q.3) The L-frame in figure below supports forces from two cables. Cable "EAD" passes through a frictionless ring at point "A", and cable "OCG" passes through a frictionless ring at point "C". The force in cable "EAD" is 800 lb and the force in cable "OCG" is 400 lb. For the cable forces applied at points "A" and "C", using the vector approach determine: a) the moment about point "B", b) the moment about point "A", and c) the moment about point "O". Z B 6 ft 6 ft 9 ft 8 ft D 8 ft E 12 ft y G
A cable and pulley system at D is used to bring a 210 kg pole (ACB) to a vertical position, as shown in the figure part (a). В Pole 1.0 m Cable 30° Pulley 5.0 m a T A D a 4.0 m (а) d АСВ A Pin Pin support plates (b) The cable has tensile force T and is attached at C. The length L of the pole is 6.0 m, the outer diameter is d = 140 mm, and the wall thickness ist = 12 mm. The pole pivots about a pin at A in figure part (b). The allowable shear stress in the pin is 54 MPa and the allowable bearing stress is 92 MPa. Find the minimum diameter of the pin at A (in mm) in order to support the weight of the pole in the position shown in the figure part (a). (Assume there is a horizontal pin support at A.) 9.43 X mm
T 30 ft Determine the sag at points C and E on the cable in the figure below (Sag at point D is given), and determine the tension in each segment. H Y 口 30 Y-(160)(10) E 40* -3011+ -30 ft- 80 30- (1) (10) 160 -50 ft- D 80* + 160 ft- 50 ft Chord C 60% 8 +-301- -30 ft- L 10 ft
Pls ans within 10 mins
Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static equilibrium in the position shown? What is the tension T in cable CD? T 3.3' Answers: LCD = TCD= i A 46° B 46 lb ft. lb D
A beam ABCD with a vertical arm CE is supported as a simple beam at A and D (see figure). A cable passes over a small pulley that is attached to the arm at E. One end of the cable is attached to the beam at point B. Cable B -6 ft (a) Cable B Shear release -6 ft- (b) (a) What is the force P in the cable if the bending moment in the beam just to the left of point C is equal numerically to 960 lb · ft? (Note: Disregard the widths of the beam and vertical arm and use centerline dimensions when making calculations.) Round your answer to the nearest whole number. P =| lb (b) Repeat (a) if a roller support is added at C and a shear release is inserted just left of C (see figure part b). Round your answer to the nearest whole number. P =| lb
Q.4) Rod AB is in the x-y plane and supported by two cables as shown. The tension in cable AC is 910 N and the tension in cable AD is 585 N. (a) Determine the angle between cables AC and AD. (b) Determine the magnitude of the combined projection of the forces in cables AC and AD onto rod AB. 2.4 m 1.2 m D 3 m C A 2.6 m 1.8 m 2.4 m
7.88 A transmission cable weighs 0.3 lb/ft and has a maximum allowable tension of 1500 lb. It is to be strung between two towers that are 2450 ft apart, horizontally, and at elevations of 7200 ft and 6500 ft, respectively (see Fig. P7.88). Determine the minimum length of cable needed. Elevation= 7200 ft 2450 ft Elevation= 6500 ft
Calculate the tension in the cable, and the reactions at A and C 100 mm 100 mm 300 mm 400 N C 400 N 250 mm B D A 150 mm 500 mm
Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static equilibrium in the position shown? What is the tension Tin cable CD? T 41° 1.7' Answers: LCD- i TCD= i B 49 lb ft lb
Member ABC, which is supported by a pin and bracket at C and a cable BD, was designed to support the 50-kN load Pas shown. Knowing that the ultimate load for cable BD is 150 kN, determine the factor of safety with respect to cable failure. 40 30° B 60 cm P 80 cm 40 cm

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

1. reactions for the cable 2. the sag y at the 45-kip load. 3. Cable length 10 ft 30 ft B +45 kips 65 kips 85 kips -30 ft 50 ft - 50 ft- + 30 ft