1. Plot the saturated line of water in P-T, P-v, and T-v diagrams from -0 °C to ~375 °C withincrements of 25 °C using Table below. Hint: plot v in logarithm scale.T(C)P (kPa)vr (m/kg)V (m/kg)0.010.61130.001206.132253.1690.00100343.35935012.350.00101212.03187538.580.0010264.13123100101.30.0010441.6729125232.10.0010650.77059150475.90.001090.392781758920.0011210.21682001553.80.0011560.127362252547.70.0011990.0784925039730.0012510.050132755941.80.0013170.0327930085810.0014040.02167325120400.0015280.0142350165140.001740.00881374.1220890.0031550.00315

The P-T curve for the given data is drawn as :

Answered: 1. Plot the saturated line of water in…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure increase of a gas was divided into three calculation paths; Arrange the temperature of each path in increasing magnitude: Isothermal compression(T1) isochoric heating(T2 adiabatic compression(T3). a.T2<T1<T3 b.T1<T2<T3 c.T1<T3<T2 d.T2<T3<T1
Determine the specific volume of superheated water vapor at P bar and T°C based on: a) the ideal-gas equation b) the generalized compressibility chart, and c) the steam tables. d) Determine the error involved in the first two cases. Select Case # 7 from the Table 1 for Pressure and Temperature Table 1 Given Pressure and Temperature Case # Pressure (bar) Temperature (°C) 1 40 440 2 40 500 40 540 4 40 600 60 440 6 60 500 7 60 540 8 60 600
A Moving to another question will save this response. Question 11 Determine the absolute pressure at a point 2 m below the free surface of sea water of specific gravity 1.025. Take atmospheric pressure as 101325 Pa. O 121.110 kPa O 101.345 kPa O 20.211 kPa O 121.436 kPa
At a certain point on the wing of the aircraft, the pressure is 37,803 Pa and the density is 45% of the standard sea level values. Determine the temperature (Kelvin) at that point? Use standard metric units and round off answer to the nearest hundredths.
ll SMART 2:18 PM O a 82% K All iCloud **Instruction: Use Given-Required-Solution in answering problems. Provide necessary diagrams for each. Answers should be rounded off to four decimal places and enclosed in a box.** 1.) Show that 1kg-m weights, 1kg-f on earth. 2.) A column arranged vertically holds a composite fluid of 46 cm of mercury (SG = 13.5), 66 cm of water (density = 1000 kg/m^3), and 81 cm of oil (SG =0.8), with its top end exposed to the atmosphere. Calculate the pressure at the bottom of the column. Knowing that fluids with higher densities sit below fluids with lower densities, illustrate the vertical column (no need to be up to scale).
both 14 and 15 please
Water flow with a density of 998 kg / m3 at 70 ° C enters the system at a speed of 0.5 m / s and a 20 cm diameter pipe is pumped to a 2.5 m high reservoir with the help of a 7.5 kW pump. With the heater at the exit of the system, 1300 kW of energy is transferred to the water flow. Calculate the exit temperature of the water. (With reference to the height Z1, Z2 = 2.5 m is acceptable, ignore kinetic energy changes.) heater Pa pump and turbine P1 Ws reference plane O--
Density is defined as mass per unit volume (Fig. 1-25). Density: (kg/m) (1-4) The reciprocal of density is the specific volume v, which is defined as vol- ume per unit mass. That is, (1-5) For a differential volume element of mass ôm and volume &V, density can be expressed as P The density of a substance, in general, depends on temperature and pres- sure. The density of most gases is proportional to pressure and inversely proportional to temperature. Liquids and solids, on the other hand, are essentially incompressible substances, and the variation of their density with pressure is usually negligible. At 20°C, for example, the density of water changes from 998 kg/m' at I atm to 1003 kg/m' at 100 atm, a change of just 0.5 percent. The density of liquids and solids depends more strongly on temperature than it does on pressure. At I atm, for example, the density of water changes from 998 kg/m at 20°C to 975 kg/m at 75 C, a change of 2.3 percent, which can still be neglected in many…
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.
In a power plant operating with water and steam, the following measurements and observations were done at various stages along the system. the pressure is 150 kPa and the enthalpy, h is 1580.115 (kJ/kg) For this case, the specific vvolume is most likely: 0.001070 2.01302 1.1594 0.5802 0.001053
calculate the saturation temperature

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS