1. Maximum Principal Stress2. Minimum Principal Stress3. Maximum Shear Stress4. Normal Stress at Failure Plane A-B5. Shear Stress at Failure Plane A-B...181.6 kPa53.6 kPa315.2 kPa315.2 kPa131.6 kPaMohr's Circle Sign Conventions:...•Compressive normal stresses are positive•Shear stresses are positive, if when theyact on two opposing faces, they tend toproduce a counterclockwise rotation.

Answered: Image /qna-images/answer/1ec3d318-3561-4a23-91a4-8598d6a14504.jpg

1. Maximum Principal Stress 2. Minimum Principal Stress 3. Maximum Shear Stress 4. Normal Stress at Failure Plane A-B 5. Shear Stress at Failure Plane A-B ... 191.6 kPa 53.6 kPa 315.2 ka 315.2 kPa 131.6 kPa Mohr's Circle Sign Conventions: ... •Compressive normal stresses are positive •Shear stresses are positive, if when they act on two opposing faces, they tend to produce a counterclockwise rotation.

1. Maximum Principal Stress 2. Minimum Principal Stress 3. Maximum Shear Stress 4. Normal Stress at Failure Plane A-B 5. Shear Stress at Failure Plane A-B ... 191.6 kPa 53.6 kPa 315.2 ka 315.2 kPa 131.6 kPa Mohr's Circle Sign Conventions: ... •Compressive normal stresses are positive •Shear stresses are positive, if when they act on two opposing faces, they tend to produce a counterclockwise rotation.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute for the Shear and Moment Equation each segment. Compute the Reactions and Draw the detailed Shear and Moment Diagram indicating values.
At the end of page there were solutions, please check it out and solve it.
A hollow circular bar of cylindrical steel is 1.5 m long and has inner and outer diameters of 40 and 60 mm. (a) What is the largest torque I can apply to the circular bar if the shear stress is not to exceed 120 MPa? (b) What is the corresponding minimum value of the shear stress in the circular bar? (answers: (a) 4084.1 N.m (b) 2722.7 N.m)
A solid circular torsional member OPQ is subjected to torsional moments as shown in the figure. The yield shear strength of the constituent material is 160 MPa.Find the absolute maximum shear stress in the member.
At a point on the free surface of a stressed body, a normal stress magnitude of S, = 51 MPa (C) and an unknown positive shear stress exist on a horizontal plane. One principal stress at the point is 11 MPa (C). The absolute maximum shear stress at the point has a magnitude of 64 MPa. Determine the unknown stresses on the horizontal and vertical planes and the unknown principal stress at the point. Sgy S Answers: O, = i MPa i MPa Txy = MPa Op2 =
Using Mohr's Circle Determine: a.) The principal planes and directions b.) The principal Stresses and directions c.) The maximum Shear stress and the corresponding normal stress and directions 10 MPa 40 MPa O 50 MPa
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 22.6 ksi, Sy = 2.2 ksi, and Sxy = 3.8 ksi. Assume β=33∘β=33∘. Determine the normal stresses σxσx and σyσy and the shear stress τxyτx⁢y at the point.
The following stress element represents the stress state at point A of the structure in the figure below. Determine the principal stresses in this condition. 52.8 MPa 26.4 MPa a. 10.94 MPa, -63.74 MPa ОЬ. -15.49 MPа, 3247 МPа -12.49 MPа, 36.47 MPа O d. 8.94 MPa, -60.74 MPa
I need the answer as soon as possible
Calculate the value of Q and t that are used in the shear formula for finding the shear stress at A. 0.3 m 0.3 m 0.2 m 0.2 m 0.4 m 0.km 0.2 m
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy-17 MPa, S, - 60 MPa, and Swy- 29 MPa. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses (ơp > op2) and the maximum in-plane shear stress Tmax acting at the point. (c) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g, see Figure 12.15 or Figure 12.16) Say Answers: MPa. Opl = MPa. MPa. Tmax = 0, =
1. If P=100kN, and the plate thickness is t=8 mm, determine the maximum axial stress in the structural component shown below.