Experiment No. 4. Introduction to Electrical Components and Equipments1.+ is an electrical instrument used to measure current. To get the measurement, it isofconnected intion2.is an electrical device containing a piece of metal that melts if the current running throughit exceeds a particular level, thereby breaking the circuit.lampwwswitchconnectibatteryadditional wires3. The above diagram shows correct way to connect an ammeter to measure current flowing through thecircuit.FalseTrue

Answered: Image /qna-images/answer/dab6d159-2376-4894-a21c-dce42164a952.jpg

1. + is an electrical instrument used to measure current. To get the measurement, it is connected in 2. is an electrical device containing a piece of metal that melts if the current running throug it exceeds a particular level, thereby breaking the circuit. www. lamp switch connect battery additional wires 3. The above diagram shows correct way to connect an ammeter to measure current flowing through the circuit. False OTrue

1. + is an electrical instrument used to measure current. To get the measurement, it is connected in 2. is an electrical device containing a piece of metal that melts if the current running throug it exceeds a particular level, thereby breaking the circuit. www. lamp switch connect battery additional wires 3. The above diagram shows correct way to connect an ammeter to measure current flowing through the circuit. False OTrue

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

How does resistance change if the length of the wire is increase? a. no change b. decreased c. increased d. cannot be determined
Which of the following is a unit for resistivity? A. ohm/meter B. ohm/meter2 С. ohт — тeter D. ohm – meter?
The following are needed to determine the current density of a conductor except: A. Current B. Resistance C. Radius D. Cross sectional area
10.) Ohm’s law may be used to determine different resistance for the series and parallel combinations of resistors. * a. The statement is true. b. The statement is false. c. The statement is neither true nor false. d. Insufficient information is given for an answer.
For a conductor the slope of the V-I graph gives a. Current b. Resistance c. Voltage d. 1/Resistance
The current flowing through a resistor is measured at several differnet voltages. What is the value of the resistor? A. 0.05 B. 20 m C. 5 m D. 20
1. Draw graphs, provided to illustrate the relationship between the potential difference across each wire and current through the wire 2. Use the graph to determine the resistance of each wire 3. Give one word for "one coulomb per second"
23. Refer to the figure below to answer the following questions. a) Determine the total resistance. b). Determine the current through the 25 ohm resistor. c). Which resistor is the hottest (Hint, most current flow)? d). Which resistor is the Coolest ?
What is amount of current flowing towards a junction in a circuit? A. Twice the amount of current going away of the junction B. The same as the amount of current going away of the junction C. half of the amount of current going away of the junction D. Zero
Two resistors are identical. They can be connected in series or in parallel. If you want the smallest equivalent resistance for the combination, how should you connect them? a. in series b. in parallel c. neither d. either way because both combinations have the same resistance
Which of the following affect the resistivity of a wire? a. length b. area of cross section c. material d. all of the above
1. Voltmeter is an electrical instrument used to measure potential difference or voltage. To get the measurement, it is connected in series 2. Voltage source and terminal voltage can be related as [Choose any one answer] 3. A constant current source supplies a electric current of 200 mA to a load of 2kO. When the load changed to 1000, the load current will be 4. Internal resistance of cell when there is current of 0.40A when a battery of 6.0V is connected to a resistor of 14.50 is ENG 4) G O A hp