1. How you can read this impulse voltage: 1.2 / 50 us and at which standard? a. Durations wave front : 1.2 tr, Wave tail duration is defined as 50 m.s (as in International Standard). b. Durations wave front: 1.2 tr, Wave tail duration is defined as 50 m.s ( as in British Standard). c. Durations wave front: 1.2 tr (where tr is the transient time), Wave tail duration is de fined as 50 m.s (as in International Standard). d. All these answer are wrong. 2. The main factor in studying High voltage engineering techniques is: a. Voltage b. Cштеnt c. Electric Field d. Current

1. How you can read this impulse voltage: 1.2 / 50 us and at which standard? a. Durations wave front : 1.2 tr, Wave tail duration is defined as 50 m.s (as in International Standard). b. Durations wave front: 1.2 tr, Wave tail duration is defined as 50 m.s ( as in British Standard). c. Durations wave front: 1.2 tr (where tr is the transient time), Wave tail duration is de fined as 50 m.s (as in International Standard). d. All these answer are wrong. 2. The main factor in studying High voltage engineering techniques is: a. Voltage b. Cштеnt c. Electric Field d. Current

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The average value of a full-wave rectified voltage with a peak value of 75 Vis a. 53 V b. 47.8 V C. 37.5 V O d. 23.9 V
The maximum peak-to-peak value of an AM wave is 120 V. The peak-to-peak value of the modulating signal is 20 V. Calculate the percentage of modulation 20 % 12% 5% 10% 0.0.
Derive the expression for conditions of oscillations
4. For the following waveforms, construct a Zener wave-shaping circuit. Include the working principle of the circuit with proper ratings. t 18.
The sinusoidal waveform displayed by the CRO is shown in Figure below. The 'time/cm' switch is on 50 ms/cm and the 'volts/cm' switch is on 1 V/cm. Calculate (a) the frequency, (b) the peak to peak voltage (c) the average voltage (d) the r.m.s voltage.
1 In a certain digital waveform, the period is two times the pulse width. The duty cycle is 50% The given hexadecimal number 2B.3116 is equivalent to 53.1428 An octal equivalent for fraction decimal number is obtained using repeated division-by-8. 2.
The waveform below is from a 70-Vac source. - 50 ms 180 V Determine: a. Vpk (ans: 98.9949 V) b. Vpk-pk (ans: 197.9899 V) c. Vrms (ans: 70 V) d. Period(ans: 100 ms) e. Frequency(ans: 10 Hz) f. Angular velocity(ans:20n rad/sec) g. Phase angle(ans: 125.0876°) h. equation of the waveform(in time domain) i. the instantaenous voltage when t = 120ms(ans: -29.0880 V) j. the angle (1st occurence)after t = 0 when the voltage is + 80 V(ans: 0.99959 °) k. the time (2nd occurence) after t = 0 when the voltage is – 10 V(ans: 63.643 ms) (ans: v(t) = 98.9949sin(20nt – 125.0876°))