1. Given the following point to point (/30) network, what is the IP address of the unknown router (labeled xxx.xXx.XXX.XXx)? XXX. XXX.XXX. XXx 189.136.123.130 2. Using the diagram below, which of the following IP addresses would be valid to assign to interface Fa0/3? Choose one answer. a. 192.168.0.16 b. 192.168.0.149 c. 192.168.0.232 Subnet A 192 168 0 128 255 255 255.192 Subnet B 192.168.0.0 255 255 255 128 Subnet C Fa0/1 XXX 192. 168.0.177 Fa0/3 2.9.2? Fa0/2 192 168.0 98 3. Up to how many hosts can be placed in the subnet which currently reads 'XX' hosts?

1. Given the following point to point (/30) network, what is the IP address of the unknown router (labeled xxx.xXx.XXX.XXx)? XXX. XXX.XXX. XXx 189.136.123.130 2. Using the diagram below, which of the following IP addresses would be valid to assign to interface Fa0/3? Choose one answer. a. 192.168.0.16 b. 192.168.0.149 c. 192.168.0.232 Subnet A 192 168 0 128 255 255 255.192 Subnet B 192.168.0.0 255 255 255 128 Subnet C Fa0/1 XXX 192. 168.0.177 Fa0/3 2.9.2? Fa0/2 192 168.0 98 3. Up to how many hosts can be placed in the subnet which currently reads 'XX' hosts?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

© T O You are given a network layout below and asked to prepare the ROUTING TABLE for the ROUTER 3 only, Assune, all network communication lines are open. In your R3 Routing table, write all four destination IP addresses and corresponding interface numbers. In your answer use the notation of 12.34.56.xx4 (which means if the fnal destination is 1234.56x, then use the interface 4) 10.10.51x 10. 10.53. R1 I R2, 10.10.70x 10.10.34.x R4 Swipe up for filters Add a caption. > L
Suppose you have the following network requirements, for Given an IP address and mask of 9.0.0.0/8, design an IP addressing scheme using VLSM? How is the efficiency of this method achieved? Use the topology in Figure to answer the questions. a. Network 1 needs to support 330 host addresses. b. Network 2 needs to support 62 host addresses. c. Network 3 needs to support 2 host addresses. d. Network 4 needs to support 520 host addresses. e. Network 5 needs to support 230 host addresses. f. Network 6 needs to support 62 host addresses. g. Network 7 needs to support 2 host addresses. h. Network 8 needs to support 2 host addresses.
37. The figure below shows the TCP Congestion Window for various transmission rounds of a TCP connection. 20 --- 18 16 14 12 10 8 4 2 4 10 12 14 16 18 20 Transmission Round What is the phase of the TCP connection between t6 and t10 (i.e. between transmission rounds 6 and 10)? a. Slow start b. Multiplicative decrease c. Congestion control d. Fast recovery e. Congestion avoidance 00 00 2. Congestion Window (MSS)
An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most significant bits are used as a network ID, and the 16 least significant bits are used as a host ID. However, the host ID cannot be all O's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network? Type your answer.
You would like to send a 2100-byte chunk of data uslng TCP from Computer A to Computer B. TCP segments are carrled In IP datagrams with a 20-byte header. IP datagrams are carrled In a data link frame with a 10-byte header. The maxlmum segment slze for TCP Is 800 bytes. The physlcal layer protocol can support a data rate of 1 Mbps. Assume a total round-trip time of 10 ms between the sender and the recelver. How many frames will need to be sent from Computer A to Computer B? What Is the size of each TCP segment? Show your work
We have an IP address of 100.120.142.34/20 Assuming that the network router is assigned the largest IP address in the range, what is the IP address of the router?
List all the static routes on each of the 4 routers required for full communication across the topology. The addresses with question marks have been relabeled. I think each router should have 3 static routes. This is using the ip route command (ip route <netid> <net mask> <next hop>)
Q1
Suppose that Organization 1 has the IP address 199.0.0.0, Organization 2 has the IP address 123.0.0.0, and Organization 3 has the IP address 187.223.0.0. a) Identify the subnet masks associated with the IP addresses of the three organizations in the routing table of a router outside the organizations. b) What is the maximum number of hosts that can be supported in each of the three organizations?
Given the topology below, write the commands to advertise the OSPFv3 networks on the Sohar router. Use the following requirements: - Enable IPv6 routing- Process ID 10 - Router IDs (Sohar router = 2.2.2.2) - Advertise Network address for each interface - LAN interface (G0/0) set to passive interface - Assign Link-Local Addresses (fe80::1) to G0/0
Suppose you open your BMCC mailbox first thing on a Monday morning and find that your messages have arrived. Assuming the BMCC server does not have access to the MAC address of the device reading these emails. Explain in detail how the ARP protocol determines which device on the LAN will be the recipient of incoming Internet data. After 22 years, the transition to IPv6 addressing is complete for around 30 percent of Internet traffic. When comparing IPv4 and IPv6 address headers, the Ethernet frames' Maximum Transmission Unit (MTU) stands out as a potential stumbling block.
. In IPv4 static route, the next hop can be identified by an IP address, exit interface, or both. Write the three route types in specifying the destination and explain one only.