1. GIVEN THE FollONING CLOSED LOOP SYSTEMS REDUCE THE BIOCK DIAGRAN TO A SINGIE TRANS FER FUNCTION

Q: explain in detail aplease

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: A single loop RLC electrical circuit can be modelled as a second order system in terms of current.…

A: Taking Laplace transform of the given equation,

Q: Calculate the Total Harmonic Distortion (IEEE 519.1992) of the following current waveform. Use…

A: Given an equation of current. To calculate the total harmonic distortion.

Q: issi R6n www Rn R6n Ra-2 n E- 19.8 V ww

A: In the given circuit R2 and R5 are in series whose resultant will be 6+3=9Ω. Then this resultant is…

Q: Can you solve the question quickly please?

A:

Q: For the circuit below, determine the MAGNITUDE of the CURRENT passing through each resistor. R₁ V₂…

A:

Q: #3. Given v1(t) =200 sin (wt + 60°) and v2(t) = 460 cos (wt -10°), find the phase angle between the…

A: In this questions We need to determine the angel between both signal.  We are solving this problem…

Q: 1 ohm 4 A 15 A + V - 2 ohms 3 ohms

A: Given

Q: For the circuit shown in Figure 1, calculate ZT and Vab. j10 S 282 o a bo 60/90° V Nab 40 2 -j5 2 ZT…

A: If n number of resistor having resistance R1,R2.....................Rn is connected in series then…

Q: BE +10V R1 20k Q1 Ve R2 15k RE 1k

A: Here i have solved it using thevenin equivalent model and kvl.

Q: Example Implement the following function with a multiplexer: 5-2 F(A, B, C, D) = (0, 1, 3, 4, 8, 9,…

A:

Q: A device can be modeled with a voltage source in series with a resistace. The device is shown in…

A: A device can be modelled with a voltage source in series with a resistance. The device is shown in…

Q: ell II. Solve for the impedance Z in the following circuit that results in maximum transfer. power…

A:

Q: #5 Find the phasors V and I corresponding to (i) v(t) = 290 cos (377t-15°) V; i(t) = -8 sin (377t +…

A:

Q: Help with setting up and solving the problem.

A: The circuit diagram is shown below: For the principle of superposition, we will determine the…

Q: The switch in the circuit below has been in in position A for a long time. At t =0, the switch moves…

A: Initial switch at position A.  At time t= 0 switch at position B Find the current io and voltage Vo…

Q: 9.26 For the differential amplifier of Fig. 9.15(a) let I = 0.2 mA, Vcc=VEE=1.5 V, VCM = -0.5 V,…

A:

Q: a) Use delta-star conversion to find a resistance between terminals 'AB' of the circuit shown in…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: The circuit pometers Rand Lore 250.50 625.50 1250, 50000 4) 25.5000 e) 1000 50 ) 40.50000 g) 626,…

A: In parallel resonance circuit, the imaginary part of conductance becomes zero. The circuit draws the…

Q: 3. For each of the following signals, calculate forward DTFT or inverse DTFT. (c) X(e") = sin (2@)…

A:

Q: 4. Replace the circuit 'seen' by the 2 mA source by its Thévenin equivalent, and use the equivalent…

A:

Q: #1. A 3-phase power system is shown in Fig. 1. A load of 60 kVA is fed from a 240 V, voltage source.…

A: In this question we need to find the following Phasor voltage of the supply source VAB Phasor line…

Q: Consider the system G(s) = a) Sketch a Nyquist plot for G(s). b) Decide the phase and gain margins.

A:

Q: 6. An FM signal with a deviation is passed through a mixer, and has its frequency reduced fivefold.…

A: Note  The mixer is used to change the frequency range of the signal without affecting the signal…

Q: Can someone explain this problem step by step?

A: Since you have posted multiple questions with multiple sub parts, we will provide the solution only…

Q: +Vcc QUESTION.2. For the power amplifier of figure, if C1 = C2 = 100 µF, R1 = R2 = R3 = 100 N, R1 =…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: A resistance temperature detector (RTD) is placed in a Wheatstone bridge as according to Figure 4.…

A:

Q: 40 mH (15.1 2) 120 L0 Rms Ve 120 µF (-j22.1 2) 102 b) Current I delivered by the voltage source

A:

Q: 90. Given the programming diagram below for a PLD, what is the logic implemented at Output X? Ο Α. O…

A:

Q: circled answers are correct, i would like to know how to get them. thank you...

A: Given: A circuit,    with, I0=8A, V0=24 V, R1=6Ω, R2=4Ω,  R3=5Ω, R4=3Ω, To find: a) Thevenin's…

Q: 1. A 100kW, 230V, shunt generator has an armature resistance and field resistance of 0.050 and…

A: Induced voltage = terminal voltage +voltage drop in armature resistance.  Generator efficiency =…

Q: Task 1. Use the KCL & KVL to find Ip. 12 mA 3 kN

A: Use KCL and KVL to find Io for the given circuit ?

Q: B. point A gnitude ection toward the bottom of the page UT

A:

Q: 20K Ω M 200 V 50 V 5ΚΩ 6ΚΩ 20 μ F. The switch has been open for a long time. It is closed at t = 0.…

A:

Q: Assignment 3 Consider the combination of resistors shown in Figure. (a) Find the equivalent…

A:

Q: Assume that switch SW2 has been in position 1 long enough to completely charge switch to position 2.…

A: Given that: The circuit is as: Here switch 2 has been in position 1 for a long time enough. The…

Q: #1. For the 2-bus single line power system shown in Fig.1, use Gauss Seidel method to find V₂. Do 3…

A: Two bus system voltage at bus 1 is fixed at V1 =1 ∠0° V line impedance between bus 1 and 2 is, Z =…