1. From the measured values of distance XY, the following trials were recorded.TrialsDistance1120.68m2120.84120.76120.64Find the probable error.b. Find the standard deviationа.с.Find the standard error

As per the given question, measured distance between XY is given for various number of trails. Hence…

Answered: 1. From the measured values of distance…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

10. An agricultural engineer measured a distance of points A and B and the following values were recorded in a series measurement. Determine the probable error of the mean and single measurement. 251.22, 251.26, 251.12, 250.99 , 250.98, 251.00
Q7:- The following data give the value of (x) and (y) for six experiments: X: 57 28 19 35 39 51 y: 32 20 38 43 37 α= Find the equation of the linear regression model of the form: y = a + b(x)? Hint: Use the following: (Σ x)(Σ x2) – (Σ x)(Σxy) 33 n(Σ x2) – (Σ x)2 - b n(Σ xy) – (Σ x)(Σy) n(Σ x2) – (Σ x)2
This activity is an exercise on computing DEFLECTIONS IN BEAMS USING AREA MOMENT METHOD. Given the beam, determine the following: For simply supported beams and overhanging beams: (a) EIy value at the midspan
A civil engineer used a 200 m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial point and the end point was found to be 1.25 m. The 30 m tape is of standard length at a temperature of 10 degrees Celsius and a pull of 50 kg. During measurement the temperature reading was 15 degrees Celsius and the tape was supported at both ends with an applied pull of 75 kg. The cross-sectional area of the tape is 6.50 mm^2, and the modulus of elasticity is 200,000 kg/mm^2. The tape has a mass of 0.075 kg/m. Take C = 0.0000116 per degrees Celsius. b) Determine the Correction due to Pull for the measured line
11. As part of a project, you have been asked to determine the adjusted height of a client's office building. To obtain sufficient redundancy in the number of observations required to perform the necessary least-squares solution, you have measured 2 distances (d. and d.) and 2 angles (0, and 0.) as depicted in the following figure. The subsequent observations and their associated uncertainties are summarized in the table below. Assume that all observations were obtained independently and that 0, is exactly 69° 18' 33".
show complete written solution
Given data: K=50 MPa Poisson ratio=0.534 Find E
I need the answer as soon as possible
An experiment was carried out to study the effect of reinforced flanges on the torsional capacity of reinforced concrete T-beams. Several different types of T-beams were used in the experiment, each with a different flange width. The beams were tested by subjecting them to combined torsion and bending to failure (elongation). Below are the results obtained for 70 cm beams and 100 cm beams (assuming normal populations) Width 70cm6.07.210.213.211.413.69.2 Width 100cm6.89.28.813.211.214.910.211.815.2 Is there evidence of a difference in the variation of torques of the two types of T-beams? Use α = 0.1
a. Direct Method (please answer)
NEED ASAP PLS!!
if for the particular measurement of the probable error of the mean is 0.075 m and the most probable value of the measurement is 365.70m the relative precision is as

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

1. From the measured values of distance XY, the following trials were recorded. Trials Distance 1 120.68m 2 120.84 3 120.76 4 120.64 a. Find the probable error. b. Find the standard deviation c. Find the standard error