1. From the given coplanar force system which consists of two forces and one couple. Replace the force couple system with force acting at A. Given Figure: 100 KN 1 m y 200 KN 50 KN 1 m 25° 300 KN.m 35° 100 KN a. Determine the resultant force acting at point A. b. Determine the Angle that the resultant makes with the x-axis. c. Determine the x and y intercepts of the Resultant Force. d. Determine the resultant couple acting at point A.

1. From the given coplanar force system which consists of two forces and one couple. Replace the force couple system with force acting at A. Given Figure: 100 KN 1 m y 200 KN 50 KN 1 m 25° 300 KN.m 35° 100 KN a. Determine the resultant force acting at point A. b. Determine the Angle that the resultant makes with the x-axis. c. Determine the x and y intercepts of the Resultant Force. d. Determine the resultant couple acting at point A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

*** *Show your correct and complete solution neatly. ASAP! Thanks. Given the vibrating system below: K4 Y(t) =Ysin30t where fc: = 30 and K1 Y=20mm Find the following: m C3 C2 C5 C4 M = 10 kg K1=100 N/m K2= 80 N/m K3=75 N/m K4= 120 N/m C1 = 20Ns/m C2= 40 Ns/m C3= 35Ns/m C4-15 Ns/m C5=10 Ns/m 1. Type of Damping 2. Equation of motion x(t). Assume Initial conditions for displacement and velocity. 3. Graph 2 cycles of the vibrating system. You can use third party app for this.
Needs Complete typed solution with 100 % accuracy.
The figure shows a person wearing weight boots and doing lower leg flexion/extension exercise in a sitting position to strengthen the quadriceps muscles and a simple mechanical model of his leg. W1 is the weight of the lower leg, W0 is the weight of the boot, the magnitude of the pulling force applied to the tibia by the quadriceps muscles through the FM patellar tendon, the magnitude of the reaction force acting on the FJ tibiofemoral joint. Point O is the center of the tibiofemoral joint, point A is the point where the patellar tendon attaches to the tibia, point B is the center of gravity of the lower leg, point C is the center of gravity of the weight boot. The distances between point O and points A, B and C were measured as a=13 cm, b=27 cm and c=36 cm, respectively. The angle that the long axis of the tibia makes with the horizontal is β=34°, the angle between the line of action of the quadriceps muscle strength and the long axis of the tibia is α=18°. Points O, A, B and C lie…
The figure shows a person wearing weight boots and doing lower leg flexion/extension exercise in a sitting position to strengthen the quadriceps muscles and a simple mechanical model of his leg. W1 is the weight of the lower leg, W0 is the weight of the boot, the magnitude of the pulling force applied to the tibia by the quadriceps muscles through the FM patellar tendon, the magnitude of the reaction force acting on the FJ tibiofemoral joint. Point O is the center of the tibiofemoral joint, point A is the point where the patellar tendon attaches to the tibia, point B is the center of gravity of the lower leg, point C is the center of gravity of the weight boot. The distances between point O and points A, B and C were measured as a=12 cm, b=24 cm and c=36 cm, respectively. The angle that the long axis of the tibia makes with the horizontal is β=39°, the angle between the line of action of the quadriceps muscle strength and the long axis of the tibia is α=16°. Points O, A, B and C lie…
In Figure.4, a car wheel balancer device is used to estimate the location/direction and mass value needed to be attached to the wheel in order to statically balance it and prevent vibration during driving. Your role is to calibrate the system measurement by constructing theoretical calculation of a sample wheel and compare it with the results of the computer. The unbalanced wheel can be modelled as in Figure.5 and the four distributed point-mass as in Table.2.
P2.30 For the mechanism in the configuration shown in Figure P2.30, three instantaneous centers are also provided. (a) Specify the types of kinematic pairs, and the number of each type, and calculate the mobility. ds stal (b) Determine the positions of the instantaneous cen- ters that have not been provided. P12wor -P2,3 DE 3. P3,5 SE no slippage Figure P2.30
Completely solve. Box the final answer. WRITE LEGIBLY OR TYPEWRITE THE SOLUTIONS. Prove that the steady-state solution is yp = 4.8 sin 3t - 7.6 cos 3
Topics Discussed: Static of Rigid Bodies, Force Vector, Addition of a System of Coplanar Forces, Cartesian Vector Please re-compute and re-solve the given, This is my answer. But I also want to see your expert answer if we land in the same solutions and answers. Please show your complete solution. Thank you.
The subject is Mechanics of Deformable Bodies
Q5
Needs Complete typed solution with 100 % accuracy.
Answered: T Blackboard @ Texas X Bb MasteringEngineering - Spring 2 × E MasteringEngineering Mastering x > (195) Find the resultant force acti X O (195) Morgan Wallen - Cover i session.masteringengineering.com/myct/itemView?assignmentProblemID=12360390 ABP G I Review Suppose that h = 4 m. (Figure 1) Part C Determine the coordinate direction angle B of the resultant force of the two forces acting on the sign at point A. Express your answer using three significant figures. B = 90 Submit Previous Answers v Correct Part D Figure 1 of 1 Determine the coordinate direction angle y of the resultant force of the two forces acting on the sign at point A. 2 m Express your answer using three significant figures. E 2 m B Hν ΑΣφ ? vec F = 350 N Fc= 400 NA F = 400 N 2 m Submit Request Answer 3 m Provide Feedback Next > 11:50 PM O Type here to search 2/7/2021