1. From a clear water reservoir 3 m deep and maximum water level F at 30.00, water is to be pumped to an elevated reservoir at 75.00 at the constant rate of 9,00,000 litres per hour. The distance is 1500 m. Give the economical diameter of the rising main and the water horse power of the pump. Neglect minor losses and take f = 0.01. %3D

1. From a clear water reservoir 3 m deep and maximum water level F at 30.00, water is to be pumped to an elevated reservoir at 75.00 at the constant rate of 9,00,000 litres per hour. The distance is 1500 m. Give the economical diameter of the rising main and the water horse power of the pump. Neglect minor losses and take f = 0.01. %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

complete solution thankyou
Complete solution pls
Water is being pumped at a steady rate of 500 gpm from a 12in diameter well. Thewell draws water from an unconfined aquifer. The height of water in the aquifer in the equilibrium statebefore pumping is 100ft, and the drawdown at the well at steady state pumping is 40ft. The hydraulicconductivity of the aquifer determined from a pump test is 0.02ft/min. Determine the radius of influence.
please consider minor and major losses
The pump whose characteristics are: H, = 80 – 600V²2 %3D n = -1500V² + 700V Elevation = 230 m |(2) (1) Elevation = 200 m 1000 m pipe 40 cm in diameter Pump Figure Q3 is used to pump water (µ=0.001kg/ms) a distance of 1000 m between two reservoirs the elevations of which are shown in Figure Q3 and remain constant. The pipe is 40 cm diameter commercial steel (ɛ=0.046 mm). Ignoring minor losses and assuming fully turbulent flow. Determine d) The volumetric flow rate e) The efficiency at the operating point
An engineer is hired to design a swimming pool 15 m long by 6 m wide by 2 m deep. For water supply, he decides to lay 600 m of 5 cm pipe with f = 0.020 from a nearby main to the pool. The pipe will discharge freely into the pool during the entire filling process. The average pressure at the water main is 550 kPa and the difference in elevation between the two ends of the pipe is 10 m, with the discharge end higher than the intake end. Assuming that 10 % of the loss in the pipeline are due to transitions, fittings, and valves, how long will it take to fill the swimming pool?
SITUATION 4: Water is drained from a large reservoir using two horizontal pipes connected in series. The first pipe is 20 m long and has a 10-cm diameter, while the second pipe is 35 m long and has a 4- cm diameter. The water level in the reservoir is 18 m above the center line of the pipe. The pipe entrance is a sharp edged, and the contraction between the two pipes is sudden. Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir. Assume the friction factor for all pipes is equal to 0.02 and the loss coefficient is 0.05 for a sharp edged entrance, and is 0.46 for sudden contraction. 18 m Oil tank 20 m 35 m
Three reservoir, named A,B, and C are connected by Pipe 1, Pipe 2, and Pipe 3 respectively joining at a common junction. Determine the into or out of the reservoir A in the pipe system, given the following data. Use n=0.011 for all pipes. Reservoir A at El. 30 m, B at El. 24 m, and C at El. 15 m Pipe 1: 30 cm dia. 1200 m long Pipe 2: 20 cm dia. 900 m long Pipe 3: 16 cm dia. 1500 m long
2] A pipe discharges 130 lps of water into a reservoir at a point 1.85 m belowthe water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25m above the water surface. At the discharge end the pipe is 30.5 cm. If the head lossfrom A to the reservoir is 0.7 m, determine the pressure in A.
answer fast
Q.solve itt.