1. For the ADC0804 used in section 1. the step size can be adjusted by setting the reference voltage on pin 9. When this pin is not connected (as shown in the figure 1 schematic), the reference voltage is the operating voltage Vcc. a) What is the step size for this default setting? b) How can we set the reference voltage on pin 9. to 4 V? c) What would be the step size after changing the reference voltage to 4 V? 2. Determine the analog input that will result in an output code of "10001110". Assume 5 V reference. Show your calculations. 3. What value of the analog input voltage would result in a digital output is 6F (hex)? Assume 4V reference. Show calculations. 4. In section, you used a 8-bit D/A converter. With a reference voltage of 5 V, what voltage does each bit represent in terms of the analog output? Show calculations. 5. For the D/A converter, if the output is 3.62 V, what is the value of the digital input? Show calculations. 6. For the D/A converter circuit shown in Figure 2, If ‘V+' reference was changed to +10 V What will be the output voltage for the digital input value of 200 (decimal)?

1. For the ADC0804 used in section 1. the step size can be adjusted by setting the reference voltage on pin 9. When this pin is not connected (as shown in the figure 1 schematic), the reference voltage is the operating voltage Vcc. a) What is the step size for this default setting? b) How can we set the reference voltage on pin 9. to 4 V? c) What would be the step size after changing the reference voltage to 4 V? 2. Determine the analog input that will result in an output code of "10001110". Assume 5 V reference. Show your calculations. 3. What value of the analog input voltage would result in a digital output is 6F (hex)? Assume 4V reference. Show calculations. 4. In section, you used a 8-bit D/A converter. With a reference voltage of 5 V, what voltage does each bit represent in terms of the analog output? Show calculations. 5. For the D/A converter, if the output is 3.62 V, what is the value of the digital input? Show calculations. 6. For the D/A converter circuit shown in Figure 2, If ‘V+' reference was changed to +10 V What will be the output voltage for the digital input value of 200 (decimal)?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2) How to calculate the value of Peak to peak voltage in a CRO? a. Vp-p = number of vertical division × (1⁄division) b. Vp-p = number of vertical division × (volts/division) c. Vp-p = (volts/division) d. Vp-p = number of vertical division × volts
In the circuit shown in Figure 3 used for full-wave rectification, which of the diodes is connected incorrectly? O a. D4 O b. D₁ O c. D₂ O d. D3 z D4 D₁ D3 D₂ Figure 3. Rectification Circuit
Q4 / three phase half wave controlled rectifier is used to feed a resistor load of ( 10 ohm) the source is (208 volt) star connected: calculate: 1- The average value of the voltage and current on the terminal load if angle (45). 2- The average of the voltage on the terminal load if angle (80). 3- The angle required to get 7 amp. 4- Draw the circuit.
Explain diagram
2. Please respond to question in attached image. Thank you.
Question 5 Assume the zener diodes are all ideal in the circuit below and let V1=3.7 V, R1=935 2, R2=1,04702, and R3=855. Determine the output voltage Vo. Express your answer in Volts and round to the 1st digit to the right of the decimal. R1 V1 D1 5V R2 D2 3V {R3 D3 2V Vo
Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm