1. For a series RC low-pass filter, component values are given as R = 10 kN and C = 0.01 µF. The amplitude of the source voltage is 10 V peak-to-peak. a) Calculate the cut-off frequency in Hz. b) Calculate V, in magnitude when the source voltage has frequencies of 0.4, 0.8, 1.2, 1.6, 2, 4, 8 kHz.

1. For a series RC low-pass filter, component values are given as R = 10 kN and C = 0.01 µF. The amplitude of the source voltage is 10 V peak-to-peak. a) Calculate the cut-off frequency in Hz. b) Calculate V, in magnitude when the source voltage has frequencies of 0.4, 0.8, 1.2, 1.6, 2, 4, 8 kHz.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: The critical frequency of a Bode Plot is 338 kHz. This filter passes low frequencies and will not…

Q: A coil of inductance 15 mH and resistance 75 2 is connected in series with a 25 9 resistor and a…

Q: a) State the circuit condition for resonance. b) Determine the circuit current at resonance.

A: Given: Vs = 12V R=10Ω C=0.1μF L=0.5H Need to calculate the resonance condition & current at…

Q: For the circuit shown: 1. Find the value of "R" that makes the circuit in resonance. 2. Determine…

A: Given figure,

Q: 16V for the given circuit: Fake 5ka a) Set the re find AVmid = loke c) zi= ? n 313

A: Note : It is the kind notice that according to the guidelines of the company we supposed to…

Q: For the network below (#7-#10), E-50 mV VR R=20 7. Which should the value of Xc for resonance? a. 00…

A: We need to analyse the given RLC circuit .

Q: A 200-MVA 15/200-kV single-phase power transformer has a resistance of 0.01352 and a reactance of…

A: Given, In single phase transformer the parameters are S=200 MVAV1/V2=15/200 kVR=0.0135 ΩX=0.0563 Ω

Q: Please Help For the circuit shown in the figure, a) Determine the voltage gain (Vout/Vin). b) Make…

A: Given:A circuit, To do:a) Determine the voltage gain (Vout/Vin).b) Make the magnitude and phase Bode…

Q: A circuit as in the figure, has a bandwidth frequency of 2400HZ, and resonance frequency of 4000 Hz.…

A: Given : Resonance frequency = fr fr = 4000 Hz Bandwidth = 2400 Hz. R = 2 ohm E = 20 m V…

Q: 3. Perform the following steps for the given circuit in below. a) Find the fL.S, fLC and fLE b)…

A: (a) Calculating different frequencies VE=VB-0.7=1.8-0.7=1.1 V Ri = R1 || R2 || βre Ri=0.49 kΩ…

Q: Series RC low-pass filter, components are: R=5kN and C=0.005 µF and the amplitude of the source…

A: The Low Pass Filter – the low pass filter only allows low-frequency signals from 0Hz to its cut-off…

Q: A constant current of 2.8 A exists in a resistor. The rms value of current is A.

A: Given: In a resistor the constant current is I=2.8 A

Q: How does the Bode diagram of a closed control loop determine whether it is stable? Select one: a.…

Q: The voltage magnification produced across L or C in the circuit at resonance is called. .

Q: A coil of inductance 15 mH and resistance 75 2 is connected in series with a 25 resistor and a…

A: Dear student Since you have posted a question with multiple sub parts, we will provide the…

Q: Find the transfer function for the circuit shown in the figure. Plot the amplitude graph of…

Q: A filter has BW = 18kHz and center frequency of 120kHz. Find the Q to the hundredths place. Round…

A: We need to find out quality factor for given centre frequency and bandwidth . We need to tell about…

Q: For the circuit shown: 1. Find the value of "Rc" that makes the circuit in resonance. 2. Calculate…

A: Given Data:- Voltage(VT)=10∠0°VResistance(RL)=8ΩInductance(XL)=j6ΩCapacitance(XC)=-j5Ω

Q: 3. Determine the expression for the resonance frequency or of this circuit. L moo Vin R₁ R₂

Q: Vin 5k 30n 5k M -15V LM324 +15V Vo Vin 100k ww 1,5n HE 100k -15V LM324 +15V Vo

Q: Design an R-C low-pass filter to have a cutoff frequency of 500 Hz using a resistor of 1.2 k. Then…

A: we need to design a RC LPF with fc= 500 Hz and R=1.2 kohm. Also we need to sketch magnitude and…

Q: 70.7% voltage loss corresponds to _% power loss and a decibel value of dB. (include appropriate sign…

A: The 70.7% voltage loss means the rms value or 1/sqrt2 value of the voltage this gives us the half…

Q: a) According to the circuit in the Figure 1: I. Write down the type of this filter (Output taken…

Q: 7. a. The bandwidth of a series resonant circuit is 200 Hz. If the resonant frequency is 2000 Hz,…

A: In this question, We need to determine the value of quality factor Q? , Reactance impedance, L and…

Q: The bode diagram of a control system for K=1 is given below. What value must K take for the gain…

A: The bode diagram of a control system for K=1 is given below: We need to find the value of K for the…

Q: Figures (a) to (e) below show the asymptotic Bode diagrams (magnitude and phase) of the constituent…

Q: Find the transfer function for the circuit shown in figure 1. Plot the amplitude graph of 2logh10hw…

A: Let us review the impedance offered by passive elements. The impedance of a capacitor reduces with…

Q: resonant LC circuit is delivering 100 W of power. What is the power value (in watts) at -3dB point?

A: We need to find out the power at -3dB point .

Q: sub= 1 urgently

A: It is given bandpass filter has equal ripple of 0.5 db Therefore, δp=δs=0.5 Attenuation frequency,…

Q: answer with explain

A: In time domain, If the time duration change double and amplification factor = 3 times then what is…

Q: Find the transfer function for the circuit shown in the figure. Plot the amplitude graph of…

Q: 04. Suppose the circuit shown has the given characteristics at resonance. Determine: a) the value of…

Q: Reactance (2) 50 2 XL X 50 × 10³ Xc R w (rad/s)

Q: Q4) List the flags that would be affected during the use of IN instruction.

A: Need to find the flags that would be affected during the use of IN instructions

Q: R L V,(t) Figure 4. The series RLC circuit. P3 For the series RLC circuit given in Figure 4 for…

A: Note: We are authorized to answer three sub parts at a time, since you have not mentioned which part…

Q: Design the pass-band filter based on series resonance with the frequency response presented in…

A: Introduction Pass-band filter It is an electronic filter. It passes frequencies within a certain…

Q: A passive RL filter circult is given below. ll + Vin out a. Determine an expression for the voltage…

Q: 4.) Given the following LRC circuit (L = .012 H, R = 8 ohm, C = 2 F, w = 2*60*pi), Vmax = 100V. A.)…

Q: a) According to the circuit in the Figure 1: I Write down the type of this filter (Output taken over…

A: as per our guidlines we are supposed to do the first question if a student asks multiple questions.…

Concept explainers

Filter

A filter is a device or process which removes some of the unwanted features or components like frequencies from a signal in signal processing. The feature of filters is the complete or partial suppression of some part of the signal, and filtering is a class of signal processing. This most often means removing some frequency bands or some frequencies. In the frequency domain, the filters do not exclusively act, especially in the image processing field many other targets for filtering exist. Without having to act in the frequency domain, the correlations can be removed for certain frequency components and not for others. The filters are widely used in electronics and telecommunication, in television, radio, radar, audio recording, music synthesis, control systems, computer graphics, and image processing.

Question

1. For a series RC low-pass filter, component values are given as R = 10 kn and C = 0.01 µF. The
amplitude of the source voltage is 10 V peak-to-peak.
a) Calculate the cut-off frequency in Hz.
b) Calculate V, in magnitude when the source voltage has frequencies of 0.4, 0.8, 1.2, 1.6, 2, 4, 8
kHz.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the transfer function for the circuit shown in the figure. Plot the amplitude graph of 2log10[H(jw)] and the phase angle graph of H(jw) Calculate the actual cutoff frequency? Calculate the true phase angle at the cutoff frequency?
(c) i. Draw the electronic circuit for a 1st order passive low pass filter,ii. Derive the transfer functions Vout/Vin in terms of capacitor C, resistor R and frequency fofthe low pass filter.iii. Draw the electronic circuit for a bandpass filter,iv. Sketch the bode plot showing the cut-off frequencies ofthe bandpass filter
In the filter shown in figure 8 the ratio between the output AC voltage Vout and input voltage Vin is given by Vout R wCR (1) R+ j(wL – 1/(wC)) Vin R+ j(w?LC – 1) - -
35
7- Draw a Band-pass Filter circuit. How does the frequency look like? Plot the graph.
Figures (a) to (e) below show the asymptotic Bode diagrams (magnitude and phase) of the constituent parts of five different open-loop transfer functions, ??(?). The Bode diagrams are colour coded. Write the transfer function corresponding to the pair of Bode plots in the space provided to the right of each figure. No need to show any working – just write the standard form of transfer function equation for each diagram.
If vsig is a triangle waveform, determine the maximum amplitude that vsig can have? Showyour calculation.
b. Choose the suitable choice foL ping of the following sentences 18 Maces 1. In order to tune a parallel resonant circuit to a lewer frequency the capacitor must a. Be increase. b. Be decrease. . BeZero. Remain the same 2. Ina very low frequency a series resonance behaves as Imost purely .......... circuit a Resistive. b Capacitive. . Inductive. d. Inductive and capacitive 3. Real part of the total impedance at resonance for complicated AC circuit is a. Positive Value. b. Zero Value. Negative Value. d. Complex value 4. For admittance locus the maximum obtained power factor is depend on a Maximum current b. Maximum voltage . Minimum power d. Minimum angle 5 Any non sinusoidal symmetrical waves are basically composite from fundamental wave plas .. of harmonics waves. aodd b. even . odd even d odd of even 6. If we append an inductance in series to an RL series circuit the time constant will be a Increases b. Decreases. Increases and Decreases. Increases or Decreases 7. The double energy…
Use the image below to help answers parts a and b.in an LRC type circuit series the inductive reactance is XL=484 ohms. and I=0.8 amps is the measured current amplitude.A) In the inductor determine the amplitude of the voltage.B)If the LRC circuit is at resonance frequency find the capacitive reactance.
4. Given the following LRC circuit below: The circuit shown has a resonant frequency, fr=100 kHz. The circuit has a resistance value, R = 10002, capacitance value, C = 1.33nF. and an inductance value of L=1.904mH. a. Determine the quality factor, Q, for the circuit b. What is the BW of this circuit? c. Calculate the upper and lower cut-off frequencies. d. If the following triangle wave with a fundamental frequency, f, of 20 kHz is put through this filter, determine the output.
i need the answer quickly
Q2 Sketch the asymptotes of the Bode plot magnitude and phase for the controlled transfer function of the system described in the figure, calculate the gain and phase: margins, Take K = 1. d42u42 S+