1. Find Reg for each of the network below. 42 10Ω 6Ω 22. 82 20 Ω Reg ww Reg 22 72 3Ω

Q: a. calculate the input dc voltage e12- b. calculate the output dc voltage of the op amp. c. If the…

A:

Q: b) A student sets up an electric circuit like the one shown in Figure Q1(b). i) Describe how a…

A: Given :   Practical current source the student in the laboratory has made the circuit.     The…

Q: Bet Bershat low -> 16 15() Ri 30 Rež

A:

Q: R Ro Lo Yük H

A:

Q: 28 * ?If 30% of a number is 12.6, find the number (abäi 2) 38 O 42 O 40 O 45 O

A: Percentage: percentage of a number can be defined as measured or defined value over the absolute…

Q: 21. Frequency is measured in a. amperes b. volts c. watts d. hertz

A: In this question, choose the correct option Unit of the frequency?

Q: subtract 58 from 29 using 15's and 16's compliment

A:

Q: Perform Analysis of above given Sequential Circuit

A: According to the question,  we need to find the expression for the output of the given circuit. Let…

Q: What is the value of ? A) 0.1 A B) IA C) -1 A D) -2 A E) 0 A 1A(1 1A(

A: Given circuit:

Q: 2- State the benefit of increasing the width of the address bus

A: There are two main types of buses in a microprocessor. These are address bus and data bus.

Q: The conducting rod of length I in the figure moves B. out without friction with velocity v. The…

A:

Q: Determine the Q-point values for Figure 1:

A:

Q: X-When several persons are electrocuted, the first to expire is the one nearest the source. Y- A…

A: X- when several persons are electrocuted the first to expire is the one nearest the source.  Y- a…

Q: the numerator is wrong please calculate again and draw the plots by hand

A: Note: Using Bode Plot (Magnitude and Phase plot) , A frequency domain system stability can be define…

Q: Find the a parameters for the circuit in (Figure 1). Suppose that R₁ = 0.7 kſ, and R₂ = 40.7 kft.…

A:

Q: Number 4  I put c as in answer and got it incorrect

A:

Q: 12 15 16 None of the other answers are true

A:

Q: 2. Determine the inductance at terminals A-B in the network in the follow diagram: ' 1mH 1mH 2mH…

A: In this question we need to find a equivalent inductance between the two terminal of the given…

Q: Question #2 Analyze the following circuit. A' A CIK T B' Cik B T C

A:

Q: .A commutator is made of segments a. Iron b. Steel O c. Copper O

A:

Q: b/ We obtained the following values from alternating voltage measurements by means of a d-organza…

A:

Q: Find current through each resistor and the nodal voltage

A: Fig: given circuit  Apply KCL at node A…

Q: L. 6 (t) dt

A:

Q: 23. What is the waveform across D1? halfwave fullwave sinewave DC line 24. What is the waveform…

A: 23. whenever diode conducts then voltage across the diode is constant i.e, for silicon diode it is…

Q: C. Perform the indicated operations (b) 13– 4i || 4+ 3i l:

A:

Q: is the aijference between the pins 4, and mention when we can use pins under number 1 and when we…

A: Pin mentioned with 1. :- Digital pin  Arduino Uno has 14 GPIO pin . Out of them pin2 to pin13 are…

Q: What is the value of I? A) 0.1 A B) IA C) -1A 1A(1 70 IA D) -2 A E) 0 A

A: Given circuit,

Q: !They asked me to .. overtime do Make

A: They asked me to........................................overtime. Make is used whenever there is a…

Q: Example 2-5. A 15-kVA, 2300/230-V transformer is to be tested to determine it excitation branch…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: MOVITG to dilouler queston will save uns Tesponse. Quèstion 13 The number 45A may be base 10 may be…

A: We are know that when Base 16 Numbers are 0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F So  From the Question The…

Q: incorrect E1=2v indeed but A2=4A please resolve the whole question correctly and in a more detailed…

A:

Q: 2.52 E 3 S2 10.3 V H. F D

A:

Q: Q1/C:-Determine whiter the circuit is operating properly and if not what is the probable cause B…

A: As we have given : β=100

Q: Electric ovens are mostly (a) resistive (b) capacitive (c) inductive (d) both a and c

A:

Q: Choose the correct instruction that will send data to an 1/0 device. IN AL, 60 O IN 60, AL OUT 60,…

A: MOV instruction : Copies the data item referred to by its second operand (i.e. register contents,…

Q: I need the solution to letter (b)

A:

Q: 11 3A Q X R1 202 Isc B R3 302 12 4A

A:

Q: The voltage across a 1 is given by g for 0. Find the current? O a. 5uA O b. 20LA O C. 15A Od. 10MA >…

A:

Q: a b C CLK clk a b X с Y D 1 6 X 2 D Q 3 7 y 4 5 8

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.