Homework Help is Here – Start Your Trial Now!
Engineering
Electrical Engineering
1. Fill the below table with the components used in building the circuit (Figure 1), and their values from the hand calculation part:

1. Fill the below table with the components used in building the circuit (Figure 1), and their values from the hand calculation part:

Introductory Circuit Analysis (13th Edition)
Introductory Circuit Analysis (13th Edition)
13th Edition
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:Robert L. Boylestad
Chapter1: Introduction
Section: Chapter Questions
Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...
See similar textbooks
icon
Related questions
Question
3. Design Components The transformation of this filter characteristic can be easily implemented using a single iow pass and high pass filter circuits isolated from each other by non-inverting voltage follower, (Av = 1). The output from these two filter circuits is then summed using a third operational amplifier connected as a voltage summer (adder) as shown in Figure 1. R= 10ko 10kn Ves As oVour Cu Summing Amplfier low-pass VINO 10 ko Ce A Rie high-pass Figure 1: Band Stop Filter Circuit 1. Fill the below table with the components used in building the circuit (Figure 1), and their values from the hand calculation part: Copyright © American College of the Middle East. 2020 Page V of 6 FL=200HZ FH=900HZ Component Name Value or Gain 3.978 kilo ohm RHP 0.884194 kilo ohm CLP 0.2 micro farad Сараcitors CHP 0.2 micro farad Amplifiers
Transcribed Image Text:3. Design Components The transformation of this filter characteristic can be easily implemented using a single iow pass and high pass filter circuits isolated from each other by non-inverting voltage follower, (Av = 1). The output from these two filter circuits is then summed using a third operational amplifier connected as a voltage summer (adder) as shown in Figure 1. R= 10ko 10kn Ves As oVour Cu Summing Amplfier low-pass VINO 10 ko Ce A Rie high-pass Figure 1: Band Stop Filter Circuit 1. Fill the below table with the components used in building the circuit (Figure 1), and their values from the hand calculation part: Copyright © American College of the Middle East. 2020 Page V of 6 FL=200HZ FH=900HZ Component Name Value or Gain 3.978 kilo ohm RHP 0.884194 kilo ohm CLP 0.2 micro farad Сараcitors CHP 0.2 micro farad Amplifiers
Expert Solution
steps

Step by step

Solved in 2 steps with 1 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Knowledge Booster
Analog to digital converters
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:
9780133923605
Author:
Robert L. Boylestad
Publisher:
PEARSON
Delmar's Standard Textbook Of Electricity
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:
9781337900348
Author:
Stephen L. Herman
Publisher:
Cengage Learning
Programmable Logic Controllers
Programmable Logic Controllers
Electrical Engineering
ISBN:
9780073373843
Author:
Frank D. Petruzella
Publisher:
McGraw-Hill Education
Fundamentals of Electric Circuits
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:
9780078028229
Author:
Charles K Alexander, Matthew Sadiku
Publisher:
McGraw-Hill Education
Electric Circuits. (11th Edition)
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:
9780134746968
Author:
James W. Nilsson, Susan Riedel
Publisher:
PEARSON
Engineering Electromagnetics
Engineering Electromagnetics
Electrical Engineering
ISBN:
9780078028151
Author:
Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:
Mcgraw-hill Education,
SEE MORE TEXTBOOKS