1. Determine the velocity of the slider D as well as the angular velocity of link 3 assuming link 2 i rotating at 100 rpm CCw. 6.0 cm B, on 2 B3 on 3 3

Q: A gear reduction system consists of two gears: E and X. Gear E rotates clockwise with a constant…

A: Given data: αE=4.5 rad/s2ωE=7 rad/s Need to determine select the correct statement.

Q: 6-14. Draw the shear and moment diagrams for the beam. 2 kip/ft A- 30 kip-ft B

A: Transverse internal force at a section is the sum of total transverse force on either the right or…

Q: Pictured below is a multiplication problem worked out using the Egyptian method and Egyptian…

A: Consider the given diagram and see row 1 and row 2.

Q: 38 17 Hole Tam delik 18 19 20 20 8 26, 20. 89

A: Given:-

Q: A 2.00-mol sample of a diatomic ideal gas expands slowly and adiabatically from a pressure of 5.02…

A:

Q: m A different pendulum has length 32 inches and is released from rest when 0 = 5° (theta = 5…

A: The length is The angle is The initial velocity is zero.

Q: A figure is scaled, using the parallel method with center of and scale factor for how do the links…

A:

Q: solve and show each step in solution

A: Step 1: Step 2: Step 3: solution is given above Step 4:

Q: Use one main program and then a subprogram to machine the pockets. Write the subprogram in absolute…

A: We must create both the main program code and the subprogram code in order to address the…

Q: Q2- the magnitude of the minimum normal stress in the beam and where within the beam it is achieved.…

A:

Q: Please. Answer parts please. Attempt Once. Use cosine and show method using both rads and degree.

A:

Q: One end of a piano wire is wrapped around a cylindrical tuning peg and the other end is fixed in…

A:

Q: Help needed in sketching thanks Several of the problems are not dimensioned. Use 5mm grid spacing…

A: Please refer the following image for the required views as per requirement.

Q: 4.21 The 40-ft boom AB weighs 2 kips; the distance from the axle A to the center of gravity G of the…

A: GivenAB=40ftw=2kipsAG=20ft

Q: 1.39 The bar AB is supported by a frictionless inclined surface at A and a 7/8- in.-diameter pin at…

A:

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: USE IMAGE BELOW! Solve for parts A through C and Label Them

A:

Q: Using the drawing below identify th mistake on dimensioning rules and write the correct method to…

A: According to DG&T standards, there are 5-dimensional mistakes that are highlighted in the fig…

Q: he Lookout Hills gravitational slope-deformation feature in Bonne Bay, western Newfour plume of rock…

A: 306m wave height has been found in norris point.

Q: a. Determine the volume in m3 of the paraboloid shown. b. Determine the centroid z in m of the…

A:

Q: 9 in. D 8 in. 12 in. W = 720 lb

A:

Q: Consider FIG-DD in the appendix.   Note: For Blocks “A” & “B” & “C”: The mass of “A” is 30 kg.…

A:

Q: Estimate the flow rate Q of water discharging from the nozzle as shown in Figure 3. If the fluid…

A:

Q: 1. Consider the system shown below. Block A weighs 95.0N and block B weighs 55.0N. Once block B is…

A:

Q: I need these 3 parts answered. In manufacturing, dimensions often may fall in a range. For example,…

A: 1-In manufacturing, dimensions often may fall in a range. For example, for three-place decimals, the…

Q: Q3: Chose and mark a datum point on the given work-piece (shown in figure 1) and mark out the…

A:

Q: Determine all support and pin forces for the frames listed below. Include force summary table for…

A:

Q: 1.50 An electric motor draws a current of 10 amperes (A) with a voltage of 110 V. The output shaft…

A:

Q: Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and…

A: Volume for each action:Cyl. A extends DE = 65 cubic inCyl. A retracts DR = 62 cubic inCyl. B extends…

Q: axis of the solid. Draw its projections, sectional front view & true shape of the section. Also…

A:

Q: 5-65 A well-insulated valve is used to throttle steam 3 MPa and 350°C to 2 MPa. Determine the final…

A: Given:Initial pressure of steam, P1=8 MPaInitial temperature of steam, T1=350°CFinal pressure of…

Q: Can you solve the problem again by taking the scale factor 13 ? Can you also draw the graphs…

A:

Q: A scene-of-the-crime-operative is called to investigate a dead body that has just been found. She…

A: Given data, 1st boundary condition At the time of death the body temperature is 37 °C, that means at…

Q: What is the temperature, in K, of the O2 in the final state?

A:

Q: To find the Mechanical Advantage of ANY simple machine when given the force, use MA = R/E. An Effort…

A: Write the value of load.   R=90 N   Write the value of effort.   E=30 N

Q: A small laboratory "mixing drum" is shown in the following figure. Drum "A" is rigidly attached to…

A: The rotation of gear C  starting from rest is The moment of inertia of gear C is The moment of…

Q: For a reactor, the following reaction rates are given by Fission rate (=[ dVE,6): 3.6×10* fissions /…

A: Part akeff=Neutron production from fission in one neutron generationNeutron absorption and leakage…

Q: For the system shown in the figure, and y denote the absolute displacements of the mass m and the…

A: Dear Students

Q: Please write what each line of G- code means for each line. Thanks

A: G codes representation in the given program

Q: The mechanism shown in figure below has been taken from a feed device for an automated ball bearing…

A:

Q: A smooth steel (SG = 7.86) sphere is dropped in glycerin. Determine its constant fall velocity using…

A: To determine the constant fall velocity of the steel sphere in glycerin using the modified…