1. Determine the reaction at the supports for the beam shown. Take E = 200 GPa and I = 90x106 m² A 2m 200 KN 2EI 3m 45 kN/m B ΕΙ 5m C

Q: Question Completion In the figure below, which of the following represents the dedendum? zeta gamma…

A: Circular pitch is the distance measured from a point on one tooth to the corresponding point on the…

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: Are you able to show an answer in terms of using formula from start to finish to get the answer…

A: Are you able to show an answer in terms of using formula from start to finish to get the answer…

Q: Iron Ore are mainly used to produce high heat in blast furnace Select one: True False CamScanner

A: Iron ore are mainly used to produce high heat in blast furnace.

Q: 20 30 R15 5-Ø10 R10 Ø40 10 40 40 Figure 1

A:

Q: What is the SAE horsepower of an 8-cylinder engine with a bore of 4.556 inches? Round to the nearest…

A: Given data:- no of cylinder (n)=8 bore (d) =4.556 inches To find:-the SAE horsepower

Q: Find the value of x5 in 3 decimal places (positive value) using Secant Method (5th Iteration) f (x)…

A: Write the given equation. fx=sinx-x take x0=0, then  f0=sin0-0=0 take x1=1, then f1=sin1-1=-0.1585

Q: The total positional tolerance equals the sum of the tolerance. O bonus and plus/minus O limit and…

A: According to the given data, we need to fill in the blank part.

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: Find the angle e for the given figure 800 N y 8 3 O a. 63 О ь. 59 с. 69 O d. 66

A: From the given figure...

Q: 4. How many datums are shown on the print? 5. What three symbols are used to describe the small…

A: What there's symbols are used to describe the small hole

Q: Iron Ore are mainly used to produce high heat in blast furnace

A: I think its answer should be False. Because blast furnace is used to melt iron ore by reducing…

Q: 200 m The spool has a mass of 40 kg and a radius of gyration of k-0.65 m. If the 20 kg weight is…

A:

Q: In the figure below, Which of the following represent the dedendum

A:

Q: question: The degrees of freedom of the calculation package in the figure?

A:

Q: Two identical cylinders methods cant be used to measure The hand writt Select one: True O False 4

A: Yes, it's true.

Q: H.W praw load dingram alesfanding to the given-Shar dingram? 2nd (urve 10 2nd Garve sfin -10 Im Im

A: BMD(Bending moment diagram) is a diagram representing the variation of bending moment along the…

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: Choose the correct word to complete the -5 following sentence: The fault was.......... .None of the…

A: Correct answer: (c) undetected

Q: An 4 cylinder engine has a crankshaft sp of 3,500 rpm, a bore of 3.8 inches, a str of 3.8 inches,…

A: Givenk=4N=3500 rpmd=3.8in =3.8×0.0254=0.09652mL=3.8in=3.8×0.0254=0.09652mP=210…

Q: Find the value of x5 in 1 decimal places (positive value) using Newton-Raphson Method f(x) = 2x2 + x…

A:

Q: Match the following. Forging is an example of Choose. Choose. Drilling operation is an example of…

A: Forging is an example of     Primary shaping process

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: The circular pattern feature can be used in creating the following part. True False

A: Circular patterns are used to draw the circular solidworks diagram as shown in the given figure.For…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: Beam deflection is to the length to a beam. OA. flexure

A: Explanation As we know that the deflection of any beam always follow the equation of elastic curve…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.