1. Determine the distance x to the center of mass of the homogeneous rod bent into the shape shown. If the rod has a mass per unit length of 1 kg/m, determine the reactions at the fixed support O.

Q: Consider steel B is a cylindrical sample with original length 40mm and subjected to 15700N.…

A: Option b is correct.

Q: A cylindric shape steel sample was tested by Rockwell hardness test and showed a hardness value 80…

A:

Q: From among the following select the truest statement. The Distortion Energy theory is a special case…

A: The given problem is based on theory of failure.

Q: What process does this following sample have gone through? I. none II. quenching III. annealing IV.…

A: ALL THE OPTION ARE HEAT TREATMENT PROCESS LIKE ANNEALLING ,QUENCHING AND COLD ROLLING .

Q: Select the appropriate Stress -Strain plot which has the highest elastic modulus from the following…

A:

Q: The volume of a 6 x 12 feet tank is 339.3 cubic feet. It contains air at 200psig and 85 Degree…

A:

Q: Suppose a dimension is indicated on an engineering drawing (with all units in inches) as 1.658 ±…

A: The lower limit of dimension= 1.658 - 0.008 = 1.650 Option third is correct.    Similarly, we can…

Q: Compare the bolt patterns in shear shown below. The distance from the load to the centroid is the…

A: following is the answer and explanation for the above question-

Q: The flow of a particular fluid is described by a velocity field given a u = x²y v = x³ = xy² w = 0…

A:

Q: Select the appropriate Stress -Strain plot which is the most brittle from the following graph A A. A…

A:

Q: erial when longitudinal strain is 0.12mm/mm and transverse strain is -0.03

A: Given data  Longitudinal strain=0.12mm/mm  Transverse strain=-0.0396mm/mm

Q: Determine the Moment of Inertia for the cross-section shown about the centroidal axis. Given M=IS…

A:

Q: From a beam bending test on a cantilever beam, the following data was collected, what is the…

A: Given: The table of mass and their respective deflections are given below, mass (g) deflection in…

Q: The meaning of Re is

A: This question is based on the concept of dimensionless number from fluid mechanics.

Q: You are designing a cantilever beam of rectangular cross-section and of fixed length. Your goal is…

A: Consider the equation shown below for the bending stress.

Q: On a spur gear tooth, for correct action, contact is allowed at any point between the pitch circle…

A:

Q: ➤ Consider FBD of pulley H: F₁, FH 54" Y TBF = 0.2666053799P = 500N TGF = 0.43137655663P = 500 N By…

A:

Q: The speed of a particle can be negative or positive, depending on the sense in which the particle…

A: It is required to evaluate given statement

Q: Annealing is a process that can release the residual stress and make the grain size grow larger,…

A: Hardness inversely proportional to squere of grain size so option a was wrong.

Q: 7. A SAE steel column has a circular cross-section of 16 mm in diameter and a length of 320 mm. The…

A:

Q: A cup and cone shape of the fracture surface for a tension tested steel sample indicates this mode…

A:

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: What is the maximum strength steel B can withstand before failure?

A:

Q: The force F shown below is applied in the positive x-direction against a 20-degree slope. The force…

A:

Q: Consider the Mass conservation equation given below: др a at ax ду Which term drops out if we assume…

A: To find : find the proper option for given expression . Given :  system is steady

Q: N

A: Given: To find: Correct rotation code

Q: The 56-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the…

A: Given:

Q: A cantilever beam (Fig. 1) has its left end fixed into a wall, and free end on the right. The…

A:

Q: ermine the force P required to force the 11° wedge under the 99-kg uniform crate which rests against…

A:

Q: Which of the following term cancels out, if we assume the flow to be fully developed along the…

A: This is a momentum equation along x direction, Apply assumption of fully developed flow condition…

Q: Calculate the horizontal force Pon the light 14° wedge necessary to initiate movement of the 58-kg…

A:

Q: The following data were obtained from impact tests performed on a ductile cast iron containing 0.30%…

A: Here ductile brittle transition temperature is the minimum temperature at which a metal can absorb…

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: Determine the force Prequired to force the 11° wedge under the 99-kg uniform crate which rests…

A: Given:-  The coefficient of friction for all the surfaces is 0.32  To Find:-  The required force…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: friction t

A: FIg:FBD Fr=μN∑Fy=0N=mgcosθ∑Fx=0μN=mgsinθμmgcosθ=mgsinθμ=tanθ

Q: Calculate the critical resolved shear stress (magnitude) in crystal if a stress of 100 MPa in the SP…

A:

Q: Which one of the folowing is not correct ?

A: Given; The maximum shear stress theory predicts that shear yieldvalue ζy is 0.5 times the tensile…

Q: 1 [Short Answer) A pitot tube is used to measure the velocity of incoming flow, the velocity is 9…

A: The velocity of flow is The static pressure is .

Q: is a measure of sensitivity of a strain gauge and is represented as the ratio of to A. BSF,…

A: Strain gauges are the devices which are used to measure the stresses in equipments or parts.

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.