I need an expert solution for handwriting, correct and complete please. 1. Design an Excess-3 (Ex-3) checker circuit for an input of 4-bits. (the output islogic 1 if the input is a valid Excess-3 and is 0 otherwise).2. Design a logic circuit with an input of 4-bit (ABCD) and one output (Y). Theoutput is logic 1 if the input is less than (4)10, and don't care when the input isgreater than (11)10.

Step 1: Step 2: Step 3: Step 4:

Answered: 1. Design an Excess-3 (Ex-3) checker…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
An X-input exclusive-OR gate and a Y-input exclusive-OR gate (where X=3, Y=4 have their outputs connected to a 2-input exclusive-NORgate. Do the following:a) Draw the logic diagram and analyze the logic expression of the output (in standard SOPform).b) List out all essential prime implicants.
Design a combinational circuit with 3-inputs and 1-output. The output is equal to logic-1 when the binary value of the input is less than 3. And the output is logic-0 otherwise.
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
H.W: Reduce the combinational logic circuit in Figure below to a minimum form.
Write a VHDL program to implement the combinational logic circuit in the following figure. HA A>B A>E B The circuit contains three input signals r, q and s, and one output sigal z. All signals are 1 bit only. In the circuit, there are two 2-to-1 multiplexers and two 2-input comparators. The two comparators should be implemented using component.
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following indicator figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, The logic "0" will be applied to the burned parts. Draw this circuit.
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following indicator figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, Logic "0" will be applied to the burned parts. The accuracy of the logic circuit you will design Create the table and find the output expressions by shrinking the table with the Karnaugh diagram method.
Logic Gates:* 7404LS (NOT)* 7408LS (AND)* 7432LS (OR)* 7400LS (NAND)* 7402LS (NOR)* 7486LS (EX-OR)Or you can use 74HCxx versions. Task 2: 4 INPUT PRIORITY ENCODERa) Write the truth table.b) Find the outputs in terms of min terms using minimal expression.c) By using K map, find the simple/simplest expression of theoutputs.d) Draw the circuit diagram. (Simulation design will be accepted.)e) Simulate the circuit & explain your results. (Please do notdesign separate simulations for each output. You should design ONEsimulation including all inputs and outputs.)
Consider two 8-bit inputs, A = $52 and B = $C3 to the arithmetic and logic unit (ALU). Compute R =A + B. Express R in the hexadecimal form $-- : -61 Express N-Z-V-C bits in the form ----:
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following display figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, Logic "0" will be applied in response to the burned parts. The accuracy of the logic circuit you will design Create the table and find the output expressions by shrinking the table with the Karnaugh diagram method.
1. Design an Excess-3 (Ex-3) checker circuit for an input of 4-bits. (the output is logic 1 if the input is a valid Excess-3 and is 0 otherwise).

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS